




Basic Function Instruction
|
T |
TIMER |
T |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Symbol
Tn: Timer Number
The total number of timers is 256 (T0~T255) with three different time bases, 0.01S, 0.1S and 1S.The default number and allocation of timers is shown as below (Can be adjusted according to user’s actual requirements by the “Configuration” function): T50~T199:0.1S timer(default as 0.0~3276.7S)。 T200~T255:1S timer(default as 0~32767S)。 FBs-PLC programming tool will lookup the timer’s time base automatically according to the “Memory Configuration” after the timer number is keyed in. Timer’s time = Time base x Preset value. In the example 1 below, the time base T0 = 0.01S and the PV value = 1000, therefore the T0 timer’s time = 0.01S x 1000 = 0S. If PV is a register, then Timer’s time = Time base x register content. Therefore, you only need to change the register content to change the timer’s time. Please refer to Example 2. The maximum error of a timer is a time base plus a scan time. In order to reduce the timing error in the application, please use the timer with a smaller time base. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Description n the time control “EN” is 1, the timer will start timing (the current value will accumulate from 0) until e Up” (i.e. CV≧PV), then the Tn contact and TUP (FO0) will change to 1. As long as the timer control input is kept as 1, even the CV of Tn has reached or exceeded the PV, the CV of the timer will nue accumulating (with M1957 = 0) until it reaches the maximum limit (32767). The Tn contact status flag will remain as 1 when CV≧PV, unless the “EN” input is 0. When “EN” input is 0, the CV of Tn will set to 0 immediately and the Tn contact and “Time Up” flag TUP will also change to 0 (please refer to the diagram c below). e FBS-PLC OS version is higher than V3.0 (inclusive), the M1957 can be set to 1 so the CV will not mulate further after “Time Up” and stops at the PV value. The default value of the M1957 is 0, fore the status of M1957 can be set before executing any timer instruction in the program to idually set the timer CV to continue accumulating or stop at the PV after “Time Up” (please refer to the diagram d below). |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

Basic Function Instruction
|
T |
Constant preset value |
Y0 |
ORG |
TIMER |
T |
||
|
Example 1 |
|||||||
|
X1 |
Ladder diagram |
Key operations |
Mnemonic code |
||||
|
ORG X 1 |
|||||||
|
.01S |
|||||||
|
EN |
T0 |
1000 |
TUP |
T0 PV: 1000 |
|||
P
|
X1 |
EN |
SET |
M1957 |
TUP |
OUT |
FO 0 |
|
.01S |
||||||
|
T1 |
1000 |
OUT Y 0 |
||||
|
ORG |
ORG SHORT |
SET M1957
|
An example of taking |
ORG |
ORGX1 |
“Time-Up” signal directly from FO0.
X1
|
Example 2 |
c |
Y0 |
or |
T0 |
0 |
1000 |
CV |
|
(CV) |
|||||||
|
M1957=0 |
0 |
1000 |
|||||
|
T0 |
|||||||
|
(Defaulted) |
|||||||
|
T1 |
|||||||
|
d |
|||||||
|
(CV) |
|||||||
|
M1957=1 |
T1 |
Time Start |
Time-Up |
||||
|
Variable PV |
The preset value (PV) shown in example 1 is a constant which is equal to 1000. This value is fixed and can not be changed once programmed. In many circumstances, the preset time of the timers needs to be varied while PLC running. In order to change the preset time of a timer, can first use a register as the PV operand (R or WX, WY…) and then the preset time can be varied by changing the register content. As shown in this example, if set R0 to100, then T becomes a 10S Timer, and hence if set R0 to 200, then T becomes a 20S Timer.

Basic Function Instruction
|
T |
Ladder diagram |
TIMER |
Mnemonic code |
T |
|
Key operations |
|
X1 |
EN |
.1S |
R 0 |
TUP |
Y0 |
ORG X 1 |
|
T50 |
T50 |
T 50 PV: R 0 |
ORG T50
|
An example of applying |
OUT Y 0 |
the “time-up” status by
using the T50 contact.
X1
200 100
T50 0
(current value)
|
c |
When R0=100 |
Y0 |
10.0S |
c |
20.0S |
d |
Time-Up |
|
When R0=200 |
Y0 |
||||||
|
d |
|||||||
|
Time Start |
Time-Up |
Remark: If the preset value of the timer is equal to 0, then the timer’s contact status and FO0 (TUP) become 1 ("EN" input must be at 1) immediately after the PLC finishes its first scan because "Time-Up" has occurred. (TUP) stays at 1 until "EN" input changes to 0.







Basic Function Instruction
|
C |
COUNTER |
C |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Symbol
Cn: The Counter number
e are total 200 16-Bit counters (C0~C199). The range of preset value is between 0~32767. C0~C139 Retentive Counters and the CV value will be retained when the PLC turns on or RUN again after a er failure or a PLC STOP. For Non Retentive Counters, if a power failure or PLC STOP occurs, the CV value will be reset to 0 when the PLC turns on or RUN again. e are total 56 32-Bit counters (C200~C255). The range of the preset value is between 0~2147483647. C200~C239 are Retentive Counters and C240~C255 are Non Retentive Counters. default number and assignment of the counters are shown below, if necessary can use the "CONFIGURATION" function to change the settings. To insure the proper counting, the sustain time of input status of CLK should greater than 1 scan time. max. counting frequency with this instruction can only up to 20Hz, for higher frequency please use the high-speed soft/hardware counter. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Description n "CLR" is at 1, all of the contact Cn, FO0 (CUP), and CV value of the counter CV are cleared to 0 and the counter stops counting. n "CLR" is at 0, the counter is allowed to count up. The Counter counts up every time the clock "CK↑" ges from 0 to 1 (adds 1 to the CV) until the cumulative current value is equal to or greater than the et value (CV>=PV), the counter "Count-Up" and the contact status of the counter Cn and FO0 (CUP) ges to 1. If the input status of clock continues to change, even the cumulative current value is equal greater than the preset value, the CV value will still accumulate until it reaches the up limit at 32767 or 483647. The contact Cn and FO0 (CUP) stay at 1 as long as CV>=PV unless the "CLR" input is set to 1.(please refer the diagram c below)。 e FBS-PLC OS version is higher than V3.0 (inclusive), the M1973 can set to 1 so the CV will not mulate further after “Count Up” and stops at the PV. M1973 default value is 0, therefore the status of 73 can be set before executing any counter instruction in the program to individually set the counter CV to continue accumulating or stops at the PV after “Count Up” (please refer to the diagram d below). |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

Basic Function Instruction
|
C |
COUNTER |
C |
|||||
|
(16-Bit: C0~C199, 32-bit: C200~C255) |
|||||||
|
Example 1 |
16-Bit Fixed Counter |
Mnemonic code |
|||||
|
Ladder diagram |
Key operations |
||||||
|
X0 |
ORG |
ORG |
SHORT |
||||
|
RST |
M1973 |
||||||
|
RST |
M1973 |
||||||
|
Y1 |
|||||||
|
ORG |
X |
0 |
|||||
|
C 1 |
CUP |
ORG |
|||||
|
PSU |
|||||||
|
X1 |
PV : |
5 |
LD |
LD |
X |
1 |
|
|
CLR |
|||||||
C 1 PV: 5
|
X0 |
SET |
M1973 |
OUT |
FO |
0 |
||||
|
X1 |
PSU |
C 2 |
CUP |
OUT |
Y |
1 |
|||
|
PV : |
5 |
||||||||
|
CLR |
ORG |
ORG |
SHORT |
||||||
|
An example of applying |
ORG |
SET |
M1973 |
||||||
|
ORG |
X |
0 |
|||||||
|
the “Count-Up” status by |
LD |
LD |
X |
1 |
|||||
|
using FO0 directly. |
C 2 PV: 5 |
||||||||
X0
X1
|
c |
C1 |
0 |
1 |
2 |
3 |
4 |
5 |
6 |
5 |
32766 |
32767 |
0 |
||
|
32767 times |
0 |
|||||||||||||
|
M1973=0 |
||||||||||||||
|
5 times |
||||||||||||||
|
(Defaulted) |
||||||||||||||
|
Y1 |
||||||||||||||
|
C2 |
0 |
1 |
2 |
3 |
4 |
|||||||||
|
d |
||||||||||||||
|
(CV) |
||||||||||||||
|
M1973=1 |
C2 |
|||||||||||||
|
Example 2 |
Count Start |
Count-Up |
||||||||||||
|
32-Bit counter with variable preset value |
||||||||||||||
Like a timer, if the PV of a counter is changed to a register (such as R, D, and so on), the counter will use the register contents as the counting PV. Therefore, only need to change the register contents to change the PV of the counter while PLC is running. Below is an example of a 32-bit counter that uses the data register R0 as the PV (in fact it is the 32-bit PV formed by R1 and R0).

Basic Function Instruction
|
C |
X0 |
COUNTER |
Mnemonic code |
C |
|||||||
|
(16-Bit: C0~C199, 32-Bit: C200~C255) |
|||||||||||
|
Ladder diagram |
Key operations |
||||||||||
|
EN |
C200 |
CUP |
ORG |
ORG |
X |
0 |
|||||
|
X1 |
CLR |
PV : |
R 0 |
LD |
LD |
X |
1 |
||||
|
C200 |
Y1 |
C200 |
|||||||||
|
ORG |
PV: R |
0 |
|||||||||
|
ORG |
C |
200 |
|||||||||
|
OUT |
OUT |
Y |
1 |
||||||||
|
An example of applying |
|||||||||||
the “time-up” status by
using the C200 contact.
X0
X1
|
c |
(R1=0) |
C200 |
0 |
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
10 |
11 |
12 |
13 |
14 |
|
4 times |
|||||||||||||||||
|
Y1 |
|||||||||||||||||
|
When R0=4 |
|||||||||||||||||
|
d |
When R0=9 |
Y1 |
Count Start |
9 times |
Count-Up |
||||||||||||
|
Count-Up |
|||||||||||||||||
Remark: If the preset value of the counter is 0 and "CLR" input also at 0, then the Cn contact status and FO0 (CUP) becomes 1 immediately after the PLC finishes its first scan because the "Count-Up" has occurred. It will stay at 1 regardless how the CV value varies until "CLR" input changes to 1.









Basic Function Instruction
|
SET DP |
SET |
SET DP |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Symbol
D: destination to be set
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Description he set control "EN" =1 or from 0 → 1 ( P instruction ), sets the bit of a coil or all bits of a register to 1. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Example 1 |
Single Coil Set |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Ladder Diagram
|
am Key Operations ORG Y 0
|
Mnemonic C ORG X SET P Y ORG X RST P Y |
odes 0 0 1 0 |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
X0 X1 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
RST Y0 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

Basic Function Instruction
|
SET DP |
Set 16-Bit Register |
SET |
SET DP |
|||||
|
(Set coil or all the bits of register to 1) |
||||||||
|
Example 2 |
||||||||
|
X0 |
Ladder Diagram |
Key Operations |
Mnemonic Codes |
|||||
|
ORG |
X |
0 |
||||||
|
P |
ORG |
|||||||
|
EN |
SET |
R 0 |
B15 |
SET P |
R |
0 |
||
|
B0 |
||||||||
|
Example 3 |
X0 |
D |
R0 |
↓ |
1 |
1 |
0 |
1 |
1 |
0 |
1 |
1 |
1 |
0 |
1 |
1 |
↓ |
||||||
|
1 0 |
0 |
0 |
|||||||||||||||||||||
|
D |
R0 |
B15 |
1 |
ØX0=• |
1 |
1 |
1 |
B0 |
|||||||||||||||
|
↓ |
↓ |
||||||||||||||||||||||
|
1 |
1 |
1 |
1 |
1 |
1 |
1 |
1 |
||||||||||||||||
|
1 1 |
1 |
1 |
|||||||||||||||||||||
|
32-Bit Register Set |
R1 |
Key Operations |
Mnemonic Codes |
||||||||||||||||||||
|
Ladder Diagram |
|||||||||||||||||||||||
|
D |
ORG |
ORG |
X |
0 |
|||||||||||||||||||
|
EN |
SET |
R 0 |
|||||||||||||||||||||
|
SET D |
R |
0 |
|||||||||||||||||||||
|
B31 |
|||||||||||||||||||||||
|
R0 |
B0 |
||||||||||||||||||||||
|
D |
R0 |
↓ |
∣ |
↓ |
|
1 0 1 10 1 1 0 1 0111011111101011 0 1 1 0 0 0 1 |
||||
ØX0=1
|
D |
R0 |
1 1 1 11 1 1 1 1 1111111111111111 1 1 1 1 1 1 1 |










Basic Function Instruction
|
RST DP |
RESET |
RST DP |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Symbol
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Description ●When the reset control "EN" =1 or from 0 → 1 ( P instruction ), resets the coil or register to 0. |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Example 1 Single Coil Reset Please refer to example 1 for the SET instruction shown in page 6-8. |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Example 2 16-Bit Register Reset
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

Basic Function Instruction
|
RST DP |
D |
R0 |
RESET |
1 |
1 |
1 |
1 |
B0 |
RST DP |
|||||||||
|
(Reset the coil or register to 0) |
||||||||||||||||||
|
B15 |
||||||||||||||||||
|
↓ |
↓ |
|||||||||||||||||
|
1 1 |
0 |
1 |
1 |
1 |
1 |
0 |
1 |
1 |
1 |
0 |
||||||||
ØX0=•
|
Example 3 |
D |
R0 |
B15 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
0 |
B0 |
|
↓ |
↓ |
||||||||||||||||
|
0 0 |
0 |
||||||||||||||||
|
32-Bit Register Reset |
Key Operations |
Mnemonic Codes |
|||||||||||||||
|
Ladder Diagram |
|||||||||||||||||
|
X0 |
D |
WM1368 |
ORG |
ORG |
X |
0 |
|
|
RST D WM1368 |
|||||||
|
EN |
RST |
||||||
|
M1399 |
WM1384 |
WM1368 |
M1368 |
||||
|
D |
WM1368 |
↓ |
∣ |
↓ |
|
0 1 10 1 1 1 0 00001101110111011 1 0 1 1 1 01 |
||||
ØX0=1
|
D |
WM1368 |
0 0 00 0 0 0 0 00000000000000000 0 0 0 0 0 00 |


Basic Function Instruction
|
FUN 0 |
MASTER CONTROL LOOP START |
FUN 0 |
|
MC |
MC |
|
Symbol |
Master control |
EN |
|
Ladder symbol |
|
|
|
0. |
N: Master Control Loop number (N=0~127) |
|||||
|
MC |
N |
the number N cannot be used repeatedly. |
||||
|
Description |
|
|
● |
There are a total of 128 MC loops (N=0~127). Every Master Control Start instruction, MC N, must |
correspond to a Master Control End instruction, MCE N, which has the same loop number as MC N. They must always be used in pairs and you should also make sure that the MCE N instruction is after the MC N instruction.
● When the Master Control input "EN/" is 1, then this MC N instruction will not be executed, as it does not exist.
● When the Master Control input "EN/" is 0, the master control loop is active, the area between the MC N and MCE N is called the Master Control active loop area. All the status of OUT coils or Timers within Master Control active loop area will be cleared to 0. Other instructions will not be executed.
|
Example |
Ladder Diagram |
Mnemonic Codes |
|||||||
|
Key Operations |
|||||||||
|
X0 |
0. |
Y0 |
ORG |
ORG |
X |
0 |
|||
|
EN |
MC |
1 |
FUN |
0 |
|||||
|
X1 |
|||||||||
|
N: |
1 |
||||||||
|
X2 |
1S |
Y1 |
ORG |
ORG |
X |
1 |
|||
|
OUT |
OUT |
Y |
0 |
||||||
|
T201 |
10 |
||||||||
|
T201 |
ORG |
ORG |
X |
2 |
|||||
|
T201 PV: |
10 |
||||||||
1.
|
X1 |
MCE |
1 |
Y2 |
ORG |
ORG |
T |
201 |
|
OUT |
OUT |
Y |
1 |
||||
|
ORG |
FUN |
1 |
1 |
||||
|
N: |
1 |
||||||
|
ORG |
X |
||||||
|
OUT |
OUT |
Y |
2 |

Basic Function Instruction
|
FUN 0 |
MASTER CONTROL LOOP START |
FUN 0 |
|
MC |
MC |
X0
X1
X2
10
T201 0
Y0
|
Y1 |
10S |
Y2
|
Remark1:MC/MCE instructions can be used in nesting or |
X0 |
MC |
0. |
1 |
|
interleaving as shown to the right: |
||||
|
MC |
Remark2:‧When M1918=0 and the master input changes from
|
0→1, and if pulse type function instructions exist in |
X1 |
MC |
0. |
2 |
|
the master control loop, then these instructions will |
||||
|
MC |
have a chance to be executed only once (when the
|
first time the master control input changes from 0→1). |
X2 |
MC |
0. |
3 |
|
Afterwards, no matter how many times the master |
MC |
control input changes from 0→1, the pulse type
|
function instructions will not be executed again. |
MC |
1. |
2 |
|
‧ When M1918=1 and the master control input |
MC |
changes from 0 →1, and if pulse type function
|
instructions exist in the master control loop, then |
MC |
1. |
1 |
|
each time the master control input changes from 0→ |
MC |
1 the pulse type function instructions in the master
|
control loop will be executed as long as the action |
MC |
1. |
3 |
|
conditions are satisfied. |
MC |
‧When a counting instruction exists in the master
control loop, set M1918 to 0 can avoid counting error.
‧When the pulse type function instructions in the
master control loop must act upon the 0→1 input
change by the master control, the flag M1918 should
be set to 1.

Basic Function Instruction
|
FUN 1 |
MASTER CONTROL LOOP END |
FUN 1 |
||||||
|
Symbol
|
||||||||
|
Description y MCE N must correspond to a Master Control Start instruction. They must always be used as a pair you should also make sure that the MCE N instruction is after the MC N instruction. After the MC N uction has been executed, all output coil status and timers will be cleared to 0 and no other instructions e executed. The program execution will resume until a MCE instruction which has the same N number as MC N instruction appears. instruction does not require an input control because the instruction itself forms a network which other uctions can not connect to it. If the MC instruction has been executed then the master control operation e completed when the execution of the program reaches the MCE instruction. If MC N instruction has never been executed then the MCE instruction will do nothing. |
||||||||
|
Description Please refer to the example and explanations for MC instruction. |
||||||||


Basic Function Instruction
|
FUN 2 |
SKIP START |
FUN 2 |
|
SKP |
SKP |
|
Symbol |
|||||
|
Skip control |
|
EN |
Ladder symbol |
|
|
|
2. |
N: Skip loop number (N=0~127), |
||||
|
SKP |
N |
N can not be used repeatedly. |
|||
|
Description |
|
|
● |
There are total 128 SKP loops (N=0~127). Every skip start instruction, SKP N, must correspond to a skip |
end instruction, SKPE N, which has the same loop number as SKP N. They must always be used as a pair and you should also make sure that the SKPE N instruction is after the SKP N instruction.
● When the skip control "EN" is 0, then the Skip Start instruction will not be executed.
● When the skip control "EN" is 1, the range between the SKP N and SKPE N which is so called the Skip active loop area will be skipped, that is all the instructions in this area will not be executed. Therefore the statuses of the discrete or registers in this Skip active loop area will be retained.
|
Example |
Ladder Diagram |
Key Operations |
Mnemonic Codes |
||||||||
|
X0 |
2. |
Y0 |
ORG |
ORG |
X |
0 |
|||||
|
EN |
SKP |
1 |
|||||||||
|
FUN |
2 |
||||||||||
|
X1 |
|||||||||||
|
X2 |
1S |
Y1 |
ORG |
N: |
1 |
||||||
|
ORG |
X |
1 |
|||||||||
|
EN |
T201 |
10 |
OUT |
OUT |
Y |
0 |
|||||
|
T201 |
|||||||||||
|
ORG |
ORG |
X |
2 |
||||||||
|
X1 |
3. |
Y2 |
ORG |
T201 PV: |
10 |
||||||
|
SKPE |
1 |
||||||||||
|
ORG |
T |
201 |
|||||||||
|
OUT |
OUT |
Y |
1 |
||||||||
|
ORG |
|||||||||||
|
FUN |
3 |
||||||||||
|
N: |
1 |
||||||||||
|
ORG |
X |
1 |
|||||||||
|
OUT |
OUT |
Y |
2 |
||||||||

Basic Function Instruction
|
FUN 2 |
SKIP START |
FUN 2 |
|||
|
X0 X1 X2 10
Y0 10S Y1 Y2 |
|||||

Basic Function Instruction
|
FUN 3 |
SKIP END |
FUN 3 |
|||||||
|
Symbol Operand
|
|||||||||
|
Description y SKPE N must correspond to a SKP N instruction. They must always be used as a pair and you should also make sure that the SKPE N instruction is behind the SKP N instruction. E instruction does not require an input control because the instruction itself forms a network which r instructions can not connect to it. If the SKP N instruction has been executed then the skip operation e completed when the execution of the program reaches the SKPE N instruction. If SKP N instruction has never been executed then the SKPE instruction will do nothing. |
|||||||||
|
Example ● Please refer to the example and explanations for SKP N instruction. SKP/SKPE instructions can be used by nesting or interleaving. The coding rules are the same as for the MC/MCE instructions. Please refer to the section of MC/MCE instructions. |
|||||||||









Basic Function Instruction
|
FUN 4 |
DIFFERENTIAL UP |
FUN 4 |
|||||||||||||||||||||||||||||||||
|
Symbol
D: a specific coil number where the result of
|
|||||||||||||||||||||||||||||||||||
|
Description DIFU instruction is used to output the up differentiation of a node status (status input to "TGU") and the e signal resulting from the status change at the rising edge of the "TGU" for one scan time is stored to a coil specified by D. The functionality of this instruction can also be achieved by using a TU contact. |
|||||||||||||||||||||||||||||||||||
|
Example The results of the following two samples are exactly the same
|
|||||||||||||||||||||||||||||||||||
|
Exam X1 |
ple T |
1 G |
4P.
|
ORG ORG FUN FUN D: |
X 4 |
1 0 |
|||||||||||||||||||||||||||||
|
Exam |
ple |
2 |
ORG ORG TU |
X |
1 |
||||||||||||||||||||||||||||||
|
X |
Y0 |
OUT OUT |
Y |
0 |
|||||||||||||||||||||||||||||||
|
X1 Y0 |
t : scan time |
||||||||||||||||||||||||||||||||||









Basic Function Instruction
|
FUN 5 P DIFD |
DIFFERENTIAL DOWN |
FUN 5 P DIFD |
||||||||||||||||||||||||||||||||||||
|
Symbol
N: a specific coil number where the result of
|
||||||||||||||||||||||||||||||||||||||
|
Description DIFD instruction is used to output the down differentiation of a node status (status input to "TGD") and pulse signal resulting from the status change at the falling edge of the"TGD" for one scan time is stored to a coil specified by D. The functionality of this instruction can also be achieved by using a TD contact. |
||||||||||||||||||||||||||||||||||||||
|
Example |
The results of the following two samples are exactly the same
ORG
|
|||||||||||||||||||||||||||||||||||||
|
E |
xam |
|||||||||||||||||||||||||||||||||||||
|
E |
xam |
p |
le |
2 |
||||||||||||||||||||||||||||||||||
|
X |
1 |
Y0 |
OUT OUT |
|||||||||||||||||||||||||||||||||||
|
X1
Y0 |
||||||||||||||||||||||||||||||||||||||


































Basic Function Instruction
|
FUN 6 DP |
BIT SHIFT |
FUN 6 DP |
|
BSHF |
(Shifts the data of the 16-bit or 32-bit register to left or to right by one bit) |
BSHF |
Symbol
Operand
D: The register number for shifting
|
Range |
WY |
WM |
WS |
TMRCTR |
HR |
OR |
SR |
ROR |
DR |
|
Ope- |
WY0 |
WM0 |
WS0 |
T0 |
C0 |
R0 |
R3904 |
R3968 |
R5000 |
D0 |
|
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
|
|
rand |
||||||||||
|
WY240 |
WM1896 |
WS984 |
T255 |
C255 |
R3839 |
R3967 |
R4167 |
R8071 |
D4095 |
|
|
D |
||||||||||
|
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○* |
○* |
○ |
Description
● When the status of clear control "CLR" is at 1, then the data of register D and FO0 will all be cleared to 0.
Other input signals are all in effect.
● When the status of clear control is "CLR" at 0, then the shift operation is permissible. When the shift control
"EN" = 1 or from 0 →1 ( P instruction), the data of the register will be shifted to right (L/R=0) or to left
(L/R=1) by one bit. The shifted-out bit (MSB when shift to left and LSB when shift to right) for both cases
will be sent to FO0. The vacated bit space (LSB when shift to left and MSB when shift to right) due to shift
operation will be filled in by the input status of fill-in bit "INB".
Example Shifts the 16-bit register data
Ladder diagram Key Operations Mnemonic Codes
ORG ORG X 1
X1 6P.BSHF Y0 LD LD X 2
EN D : R 3 OTB
LD LD X 3
X2
INB LD LD X 4
X3 FUN FUN 6P
L/R
D: R 3
X4
CLR FO 0
OUT OUT Y 0
B15 B0
X3=1
←←←←←←←←←←←←←←←←←←
(Left shift) Y0 Shifts the 16-bit data to left by one bit X2
B15 B0
X3=0
→→→→→→→→→→→→→→→→→→
(Right shift) X2 Shifts the 16-bit data to right by one bit Y0
























Basic Function Instruction
|
FUN 7 DP |
UP/DOWN COUNTER |
FUN 7 DP |
|
UDCTR |
(16-bit or 32-bit up and down 2-phase Counter) |
UDCTR |
Symbol
Operand
CV: The number of the Up/Down Counter
PV: Preset value of the counter or it’s
register number
|
Range |
WX |
WY |
WM |
WS |
TMRCTR |
HR |
IR |
OR |
SR |
ROR |
DR |
K |
|
Ope- |
WX0 |
WY0 |
WM0 |
WS0 |
T0 |
C0 |
R0 |
R3840 |
R3904 |
R3968 |
R5000 |
D0 |
16/32-bit |
|
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
+/− number |
|
|
rand |
WX240 |
WY240 |
WM1896 |
WS984 |
T255 |
C255 |
R3839 |
R3903 |
R3967 |
R4167 |
R8071 |
D4095 |
|
|
CV |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○* |
○* |
○ |
○ |
|
PV |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
Description
● When the clear control “CLR” is 1, the counter’s CV will be reset to 0 and the counter will not be able to count.
● When the clear control “CLR” is 0, counting will then be allowed. The nature of the instruction is a P instruction. Therefore, when the count-pulse “PLS” is from 0→1 (rising edge), the CV will increased by 1 (if U/D=1) or decreased by 1 (if U/D=0).
● When CV=PV, FO0(“Count-Up) will change to 1”. If there are more clocks input, the counter will continue counting which cause CV≠PV. Then, FO0 will immediately change to 0. This means the “Count-Up” signal will only be equal to 1 if CV=PV, or else it will be equal to 0 (Care should be taken to this difference from the “Count-Up” signal of the general counter).
● The upper limit of up count value is 32767 (16-bit) or 2147483647 (32-bit). After the upper limit is reached, if another up count clock is received, the counting value will become –32768 or -2147483648 (the lower limit of down count).
● The lower limit of down count value is -32767 (16-bit) or -2147483647 (32-bit). After the lower limit is reached, if another down count clock is received, the counting value will become 32768 or 2147483648 (the upper limit of up count).
● If U/D is fixed as 1, the instruction will become a single-phase up count counter. If U/D is fixed as 0, the instruction will become a single-phase down count counter.








Basic Function Instruction
|
FUN 7 DP UDCTR |
UP/DOWN COUNTER |
FUN 7 DP UDCTR |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
X16 X17 X18
Y0 Remark 1: Since the counting operation of UDCTR is implemented by software scanning, therefore if the clock speed is faster than the scan speed, lose count may then happen (generally the clock should not exceed 20Hz depending on the size of the program). Please use the software or hardware high-speed counter in the PLC. Refer to the “High Speed Counter Application” in the Advanced Manual. Remark 2: In order to ensure the proper counting, the sustain time of the status of clock input should greater than 1 scan time. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

Basic Function Instruction
|
FUN 8 DP |
MOVE |
FUN 8 DP |
|
MOV |
(Moves data from S to D) |
MOV |
Description
|
Move control |
EN |
Ladder symbol |
Operand |
|
8DP.MOV |
S: Source register number |
||
|
S : |
|||
|
D: Destination register number |
|||
|
D : |
|||
|
The S, N, D may combine with V, Z, P0~P9 to serve |
indirect addressing
|
Range |
WX |
WY |
WM |
WS |
TMRCTR |
HR |
IR |
OR |
SR |
ROR |
DR |
K |
XR |
|
|
Ope- |
WX0 |
WY0 |
WM0 |
WS0 |
T0 |
C0 |
R0 |
R3840 |
R3904 |
R3968 |
R5000 |
D0 |
16/32-bit |
V、Z |
|
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
P0~P9 |
||
|
+/− number |
||||||||||||||
|
rand |
WX240 |
WY240 |
WM1896 |
WS984 |
T255 |
C255 |
R3839 |
R3903 |
R3967 |
R4167 |
R8071 |
D4095 |
||
|
S |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
D |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○* |
○* |
○ |
○ |
|||
Description
● Move (write) the data of S to a specified register D when the move control input "EN" =1 or from 0 to 1 ( P instruction).
|
Example |
Writes a constant data into a 16-bit register. |
Mnemonic Codes |
|||
|
Ladder Diagram |
Key Operations |
||||
|
ORG |
ORG |
X |
0 |
||
|
X0 |
EN |
8P.MOV |
S |
K |
10 |
FUN |
8P |
10 |
|
|
S : |
10 |
||||||||
|
D : |
R 0 |
S: |
|||||||
|
D: R |
0 |
||||||||
ØX0=•
|
D |
R0 |
10 |

Basic Function Instruction
|
FUN 9 DP |
MOVE INVERSE |
FUN 9 DP |
|
MOV/ |
(Inverts the data of S and moves the result to a specified device D) |
MOV/ |
Symbol
|
Move control |
EN |
Ladder symbol |
Operand |
|
9DP.MOV/ |
S: Source register number |
||
|
S : |
|||
|
D: Destination register number |
|||
|
D : |
|||
|
S, N, D may combine with V, Z, P0~P9 to serve |
indirect addressing
|
Range |
WX |
WY |
WM |
WS |
TMRCTR |
HR |
IR |
OR |
SR |
ROR |
DR |
K |
XR |
|
|
Ope- |
WX0 |
WY0 |
WM0 |
WS0 |
T0 |
C0 |
R0 |
R3840 |
R3904 |
R3968 |
R5000 |
D0 |
16/32-bit |
V、Z |
|
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
|||
|
+/− number |
||||||||||||||
|
rand |
WX240 |
WY240 |
WM1896 |
WS984 |
T255 |
C255 |
R3839 |
R3847 |
R3967 |
R4167 |
R8071 |
D4095 |
P0~P9 |
|
|
S |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
D |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○* |
○* |
○ |
○ |
|||
Description
● Inverts the data of S (changes the status from 0 to 1 and from 1 to 0) and moves the results to a specified register D when the move control input "EN" =1 or from 0 to1 ( P instruction).
|
Example |
Moves the inverted data of a 16-bit register to another 16-bit register. |
|||||||
|
Ladder Diagram |
Key Operations |
Mnemonic Codes |
||||||
|
ORG |
ORG |
X |
0 |
|||||
|
X0 |
EN |
9.MOV/ |
FUN |
9 |
||||
|
S : |
R 0 |
|||||||
|
D : |
WY 8 |
S: R |
0 |
|||||
|
D: WY |
8 |
|||||||
|
B15 |
B0 |
|||||||
|
S |
R0 |
0 1 0 1 |
0 |
1 |
0 |
1 |
0 |
1 |
0 |
1 |
0 |
1 |
0 |
1 |
5555H |
|
|
D |
WY8 |
Y23 |
1 |
ØX0=1 |
0 |
1 |
0 |
1 |
0 |
1 |
Y8 |
AAAAH |
||||
|
↓ |
↓ |
|||||||||||||||
|
0 |
1 |
0 |
1 |
|||||||||||||
|
1 0 1 0 |
0 |
|||||||||||||||







Basic Function Instruction
|
FUN 10 TOGG |
TOGGLE SWITCH |
FUN 10 TOGG |
||||||||||||||||||||||||||||||||||||||
|
Symbol
|
||||||||||||||||||||||||||||||||||||||||
|
Description coil D changes its status (from 1 to 0 and from 0 to 1) each time the input "TGU"is triggered from 0 to ing edge). |
||||||||||||||||||||||||||||||||||||||||
|
Example
|
||||||||||||||||||||||||||||||||||||||||


















Basic Function Instruction
|
FUN 11 DP |
ADDITION |
FUN 11 DP |
|
(+) |
(Performs addition of the data specified at Sa and Sb and stores the result in D) |
(+) |
|
Symbol |
|
Operand |
|||||||||||||||||||||||||
|
|
|
IR |
|||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|||||||||||||||||||||
|
Sa: Augend |
|||||||||||||||||||||||||||
|
Sb: Addend |
|||||||||||||||||||||||||||
|
D : Destination register to store the results |
|||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
of the addition |
|||||||||||||||||||
|
Sa, Sb, D may combine with V, Z, P0~P9 |
|||||||||||||||||||||||||||
|
to serve indirect addressing |
|||||||||||||||||||||||||||
|
WY |
WM |
WS |
CTR |
HR |
|||||||||||||||||||||||
|
Range |
WX |
OR |
SR |
ROR |
DR |
K |
XR |
||||||||||||||||||||
|
WX0 |
WY0 |
WM0 |
WS0 |
T0 |
C0 |
R0 |
R3840 |
R3904 |
R3968 |
R5000 |
D0 |
16/32-bit |
V、Z |
||||||||||||||
|
Ope- |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
P0~P9 |
||||||||||||||
|
+/− number |
|||||||||||||||||||||||||||
|
rand |
WX240 |
WY240 |
WM1896 |
WS984 |
T255 |
C255 |
R3839 |
R3903 |
R3967 |
R4167 |
R8071 |
D4095 |
|||||||||||||||
|
Sa |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|||||||||||||
|
Sb |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|||||||||||||
|
D |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○* |
○* |
○ |
○ |
||||||||||||||||
|
Description |
|
|
● |
Performs the addition of the data specified at Sa and Sb and writes the results to a specified register D |
when the add control input "EN" =1 orfrom 0 to 1 ( P instruction). If the result of addition is equal to 0 then set FO0 to 1. If carry occurs (the result exceeds 32767 or 2147483647) then set FO1 to 1. If borrow occurs (adding negative numbers resulting in a sum less than -32768 or -2147483648), then set the FO2 to 1. All the FO statuses are retained until this instruction is executed again and overwritten by a new result.
|
Example |
16-bit addition |
Mnemonic Codes |
|||||||||
|
X0 |
Ladder Diagram |
Y0 |
ORG |
Key Operations |
|||||||
|
11P.(+) |
ORG |
X |
0 |
||||||||
|
EN |
Sa : |
R |
0 |
D=0 |
OUT |
FUN |
11P |
||||
|
Sb : |
R |
1 |
Sa: R |
0 |
|||||||
|
U/S |
D : |
R |
2 |
CY |
|||||||
|
Sb: R |
1 |
||||||||||
|
BR |
D: |
R |
2 |
||||||||
|
FO |
1 |
||||||||||
|
OUT |
Y |
0 |
|||||||||
|
Sa |
R0 |
12345 |
R0+R1=32770 |
||||||||
|
Sb |
R1 |
20425 |
|||||||||
ØX0=•
|
D |
R2 |
2 |
32768+2=32770 |
Y0=1 (carry 1 represents +32768)









Basic Function Instruction
|
FUN 12DP (−) |
SUBTRACTION |
FUN 12DP (−) |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Symbol
12DP.(-)
Sa, Sb, D may combine with V, Z, P0~P9
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Description |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
● Perf whe 0 the |
orm n th n |
s the subtraction of th e subtract control inpu set FO0 to 1. If carry |
e data specified at Sa and Sb and writes the results to a specifie t "EN" =1 orfrom 0 to 1 ( P instruction). If the result of subtractio occurs (subtracting a negative number from a positive number a |
d register D n is equal to nd the result |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
exce |
ed tiv O |
s 32767 or 214748364 e number and the res statuses are retained |
7), then set FO1 to 1. If borrow occurs (subtracting a positive nu ulted difference is less than -32768 or -2147483648), then set F until this instruction is executed again and overwritten by a new re |
mber from a O2 to 1. All sult. |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Example |
16-bit subtraction Ladder Diagram 12P.(-)
Sb R1 D R2 Y2=1( |
ØX0=1 |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Ladder Diagram
Sb R1 D R2 Y2=1( |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||











Basic Function Instruction
|
FUN 13 DP (*) |
MULTIPLICATION |
FUN 13 DP (*) |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Symbol
P0~P9 to serve indirect addressing
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Description orms the multiplication of the data specified at Sa and Sb and writes the results to a specified register en the multiplication control input "EN" =1 or from 0 to 1( P instruction). If the product of multiplication is equal to 0 then set FO0 to 1. If the product is a negative number, then set FO1 to 1. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Example 1 16-bit multiplication
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||







Basic Function Instruction
|
FUN 13 DP (*) |
MULTIPLICATION |
FUN 13 DP (*) |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Example 2 32-bit multiplication
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||











Basic Function Instruction
|
FUN 14DP (/) |
DIVISION |
FUN 14DP (/) |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Symbol
Sa, Sb, D may combine with V, Z, P0~P9 to serve indirect addressing
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Description orms the division of the data specified at Sa and Sb and writes the quotient and remainder to registers ified by register D when the division control input "EN" =1 or from 0 to 1 ( P instruction). If the quotient of ion is equal to 0 then set FO0 to 1. If the divisor Sb=0 then set the error flag FO1 to 1 without executing nstruction. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Example 1 16-bit division
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||








Basic Function Instruction
|
FUN 14DP |
DIVISION |
FUN 14DP |
|||||||||||
|
(/) |
(Performs division of the data specified at Sa and Sb and stores the result in D) |
(/) |
|||||||||||
|
Example 2 |
32-bit division |
||||||||||||
|
X0 |
Ladder Diagram |
Key Operations |
Mnemonic Codes |
||||||||||
|
EN |
14D.(/) |
0 |
D=0 |
ORG |
ORG |
X |
0 |
||||||
|
Sa: |
R |
FUN |
14D |
||||||||||
|
Sb: |
R |
2 |
Sa: R |
0 |
|||||||||
|
U/S |
D : |
R |
4 |
ERR |
Sb: R |
2 |
|||||||
|
D: |
R |
4 |
|||||||||||
|
Sa |
R1 |
R0 |
Dividend |
||||||||||
|
2147483647 |
|||||||||||||
|
÷ |
Sb |
R3 |
1234567 |
R2 |
Divisor |

|
D |
R7 |
R6 |
R5 |
1739 |
R4 |
|
571634 |
|||||
|
Remainder |
Quotient |
||||













Basic Function Instruction
|
FUN 15DP INCREMENT (+1) (Adds 1 to the D value) |
FUN 15DP (+1) |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
D : The register to be increased
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
● Adds 1 to the register D when the increment control input "EN" =1 orfrom 0 to 1( P instruction). If the value of D is already at the upper limit of positive number 32767 or 2147483647, adding one to this value will change it to the lower limit of negative number -32768 or -2147483648. At the same time, the overflow flag FO0 (OVF) is set to 1. |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Example 16-bit increment register
D When V=100,0+100=100
ØX0=• Mnemonic code X 0 15
D When V=100,0+100=100
ØX0=• |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||








Basic Function Instruction
|
FUN 16DP (-1) |
DECREMENT |
FUN 16 DP (-1) |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
serve indirect addressing
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Description racts 1 from the register D when the decrement control input "EN" =1 orfrom 0 to 1 ( P instruction). If alue of D is already at the lower limit of negative number -32768 or -2147483648, subtracting one from value will change it to the upper limit of positive number 32767 or 2147483647. At the same time, the underflow flag FO0 (UDF) is set to 1. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Example 16-bit decrement register
D : R 0
ØX0=•
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||

Basic Function Instruction
|
FUN 17DP CMP Compare control Unsign/Sign |
COMPARE |
FUN 17DP |
||||
|
(Compares the data of Sa and Sb and outputs the results to function Outputs) |
CMP |
|||||
|
Ladder symbol |
Operand |
|||||
|
17DP.CMP |
||||||
|
EN |
Sa : |
a = b |
Sa=Sb (FO0) |
Sa: The register to be compared |
||
|
Sb : |
Sb: The register to be compared |
|||||
|
U/S |
a > b |
Sa>Sb (FO1) |
Sa, Sb may combine with V, Z, P0~P9 to |
|||
serve indirect addressing
|
● |
a < b |
Sa<Sb (FO2) |
|||||||||||||
|
Range |
WX |
WY |
WM |
WS |
TMR |
CTR |
HR |
IR |
OR |
SR |
ROR |
DR |
K |
XR |
|
|
Ope- |
WX0 |
WY0 |
WM0 |
WS0 |
T0 |
C0 |
R0 |
R3840 |
R3904 |
R3968 |
R5000 |
D0 |
16/32 bit |
V、Z |
|
|
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
+/-number |
P0~P9 |
||
|
rand |
|||||||||||||||
|
WX240 |
WY240 |
WM1896 |
WS984 |
T255 |
C255 |
R3839 |
R3903 |
R3967 |
R4167 |
R8071 |
D4095 |
||||
|
Sa |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
Sb |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|
|
Compares the data of Sa and Sb when the compare control input "EN" =1 or from 0 to 1 ( P instruction). If the |
|||||||||||||||
data of Sa is equal to Sb, then set FO0 to 1. If the data of Sa>Sb, then set FO1 to 1. If the data of Sa<Sb,
then set FO2 to 1. If the data of Sa < Sb, then set the FO2 to 1.
Example Compares the data of 16-bit register
Ladder diagram Key operations Mnemonic code
X0 17.CMP ORG ORG X 0
EN Sa : R 0 a=b FUN 17
Sb : R 1
Sa : R 0
U/S a>b
Sb : R 1
Y0
a<b FO 2
OUT OUT Y 0
● From the above example, we first assume the data of R0 is 1 and R1 is 2, and then compare the data by
executing the CMP instruction. The FO0 and FO1 are set to 0 and FO2 (a<b) is set to 1 since a<b.
● If you want to have the compound results, such as≧、≦、< > etc., please send =、< and > results to relay first
and then combine the result from the relays.
● M1919=0, when this command in not executed, FO0, FO1, FO2 will remain in the status at last execution.
● M1919=1, when this command in not executed, FO0, FO1, FO2 are all cleared to 0.
● Control M1919 properly to obtain memory-holding function for functional command output.





















Basic Function Instruction
|
FUN 18DP |
LOGICAL AND |
FUN 18DP |
|
AND |
AND |
Operand
Sa: The register to be ANDed
Sb: The register to be ANDed
D : The register to store the result of AND
The Sa, Sb, D may combine with V, Z, P0~P9 to
serve indirect addressing application
|
● |
Range |
WX |
WY |
WM |
WS |
TMRCTR |
HR |
IR |
OR |
SR |
ROR |
DR |
K |
XR |
|||
|
Ope- |
WX0 |
WY0 |
WM0 |
WS0 |
T0 |
C0 |
R0 |
R3840 |
R3904 |
R3968 |
R5000 |
D0 |
16/32 bit |
V、Z |
|||
|
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
+/-number |
P0~P9 |
||||
|
rand |
WX240 |
WY240 |
WM1896 |
WS984 |
T255 |
C255 |
R3839 |
R3903 |
R3967 |
R4167 |
R8071 |
D4095 |
|||||
|
Sa |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|||
|
Sb |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|||
|
D |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○* |
○* |
○ |
○ |
||||||
|
Performs logical AND operation for the data of Sa and Sb when the operation control input "EN" =1 or from 0 |
|||||||||||||||||
to 1( P instruction). This operation compares the corresponding bits of Sa and Sb (B0~B15 or B0~B31). The bit in the D is set to 1 if both of the corresponding bits data of Sa and Sb is 1. The bit in the D is set to 0 if one of the corresponding bits is 0.
|
Example |
Operation of 16-bit logical AND |
1 |
ORG |
Key operations |
0 |
1 |
1 |
Mnemonic code |
||||||||||||
|
Ladder diagram |
||||||||||||||||||||
|
ORG X 0 |
||||||||||||||||||||
|
X0 |
18P.AND |
1 |
0 |
1 |
1 |
0 |
1 |
1 |
FUN 18P |
|||||||||||
|
EN |
Sa : |
R |
0 |
D=0 |
||||||||||||||||
|
Sa : R 0 |
||||||||||||||||||||
|
Sb : |
R |
1 |
||||||||||||||||||
|
D : |
R |
2 |
Sb : R 1 |
|||||||||||||||||
|
D : |
R |
2 |
||||||||||||||||||
|
B15 |
||||||||||||||||||||
|
B0 |
||||||||||||||||||||
|
↓ |
↓ |
|||||||||||||||||||
|
Sa |
R0 |
1 0 1 |
0 |
1 |
||||||||||||||||
|
Sb |
R1 |
1 1 1 |
0 |
1 |
1 |
1 |
0 |
1 |
0 |
1 |
0 |
0 |
1 |
1 |
0 |
|||||
ØX0=•
|
D |
R2 |
B15 |
0 |
1 |
0 |
1 |
0 |
0 |
0 |
1 |
0 |
0 |
1 |
0 |
B0 |
|
↓ |
↓ |
||||||||||||||
|
1 0 1 |
0 |














Basic Function Instruction
|
FUN 19DP OR |
LOGICAL OR |
FUN 19DP OR |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
The Sa, Sb, D may combine with V, Z, P0~P9 to serve indirect addressing
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
● Performs logical OR operation for the data of Sa and Sb when the operation control input "EN" =1 or from 0 to 1( P instruction). This operation compares the corresponding bits of Sa and Sb (B0~B15 or B0~B31). The bit in the D is set to 1 if one of the corresponding of Sa or Sb is 1. The bit in the D is set to 0 if both of the corresponding bits of Sa and Sb is 0. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Example Operation of 16-bit logical OR
ØX0=1
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||














Basic Function Instruction
|
FUN 20DP |
BIN TO BCD CONVERSION |
FUN 20DP |
|||||||||
|
→BCD |
(Converts BIN data of the device specified at S into BCD and stores the result in D) |
→BCD |
|||||||||
|
|
|
||||||||||
|
|
|
|
|
|
|
|
|
|
S : The register to be converted |
||
|
D : The register to store the converted data |
|||||||||||
|
(BCD code) |
|||||||||||
|
The S, D may combine with V, Z, P0~P9 to serve |
|||||||||||
indirect addressing
|
Range |
WX |
WY |
WM |
WS |
TMRCTR |
HR |
IR |
OR |
SR |
ROR |
DR |
K |
XR |
||||
|
Ope- |
WX0 |
WY0 |
WM0 |
WS0 |
T0 |
C0 |
R0 |
R3840 |
R3940 |
R3968 |
R5000 |
D0 |
16/32 bit |
V、Z |
|||
|
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
+/- number |
P0~P9 |
||||
|
rand |
WX240 |
WY240 |
WM1896 |
WS984 |
T255 |
C255 |
R3839 |
R3903 |
R3967 |
R4167 |
R8071 |
D4095 |
|||||
|
S |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|||
|
D |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○* |
○* |
○ |
○ |
||||||
|
● |
FB-PLC uses binary code to store and to execute calculations. If want to send the internal PLC data to the |
||||||||||||||||
external displays such as seven-segment displays, it is more convenient for us to read the result on screen by converting the BIN data to BCD data. For example, it is more clear for us to read the reading "12" instead of the binary code "1100."
● Converts BIN data of the device specified at S into BCD and writes the result in D when the operation control input "EN" =1 orfrom 0 to 1 ( P instruction). If the data in S is not a BCD value (0~9999 or 0~9999999), then the error flag FO0 is set to 1 and the old data of D are retained.
|
Example |
16-bit BIN to BCD conversion |
ORG |
Key operations |
Mnemonic code |
||||||||||||||||||
|
X0 |
Ladder diagram |
1 |
0 |
0 |
1 |
1 |
||||||||||||||||
|
ORG X 0 |
||||||||||||||||||||||
|
20. |
BCD |
0 |
1 |
1 |
1 |
0 |
0 |
0 |
||||||||||||||
|
FUN 20 |
||||||||||||||||||||||
|
EN |
S : |
9999 |
ERR |
|||||||||||||||||||
|
S : 9999 |
||||||||||||||||||||||
|
D : |
R |
0 |
||||||||||||||||||||
|
D : R |
0 |
|||||||||||||||||||||
|
B15 |
||||||||||||||||||||||
|
B0 |
||||||||||||||||||||||
|
↓ |
↓ |
|||||||||||||||||||||
|
S |
K |
0 0 |
1 |
1 |
||||||||||||||||||
ØX0=1
|
D |
R0 |
B15 |
0 |
1 |
1 |
0 |
0 |
1 |
1 |
0 |
0 |
1 |
1 |
0 |
0 |
B0 |
|
↓ |
↓ |
|||||||||||||||
|
1 0 |
1 |














Basic Function Instruction
|
FUN 21DP |
BCD TO BIN CONVERSION |
FUN 21DP |
||||||||
|
→BIN |
(Converts BCD data of the device specified at S into BIN and stores the result in D) |
→BIN |
||||||||
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
S : The register to be converted |
||
|
D : The register to store the converted data |
||||||||||
|
(BIN code) |
||||||||||
|
The S, D may combine with V, Z, P0~P9 to |
||||||||||
serve indirect addressing
|
Range |
WX |
WY |
WM |
WS |
TMRCTR |
HR |
IR |
OR |
SR |
ROR |
DR |
XR |
||||||
|
WX0 |
WY0 |
WM0 |
WS0 |
T0 |
C0 |
R0 |
R3840 |
R3904 |
R3968 |
R5000 |
D0 |
V、Z |
||||||
|
Ope- |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
∣ |
||||||
|
rand |
WX240 |
WY240 |
WM1896 |
WS984 |
T255 |
C255 |
R3839 |
R3903 |
R3967 |
R4167 |
R8071 |
D4095 |
P0~P9 |
|||||
|
S |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
|||||
|
D |
○ |
○ |
○ |
○ |
○ |
○ |
○ |
○* |
○* |
○ |
○ |
|||||||
|
● |
The decimal (BCD) data must be converted to binary (BIN) data first in order for PLC to accept the data |
|||||||||||||||||
which is originally in decimal unit (BCD code) inputted from external device such as digital switch because the BCD data can not be accepted by PLC for its operations.
● Converts BCD data of the device specified at S into BIN and writes the result in D when the operation control input "EN" =1 or from 0 to 1 ( P instruction). If the data in S is not in BCD, then the error flag FO0 is set to 1 and the old data of D are retained.
● Constant is converted to BIN automatically when store in program and can not be used as a source operand of this function.
|
Example |
16-bit BCD to BIN conversion |
ORG |
Key operations |
Mnemonic code |
|||||||||||||||||
|
X0 |
Ladder diagram |
1 |
1 |
1 |
0 |
1 |
|||||||||||||||
|
21P. BIN |
2 |
3 |
ORG X |
0 |
|||||||||||||||||
|
FUN 21P |
|||||||||||||||||||||
|
EN |
S : |
WX 0 |
ERR |
||||||||||||||||||
|
D : |
R |
1 |
S : WX 0 |
||||||||||||||||||
|
D : R |
1 |
||||||||||||||||||||
|
X15 |
|||||||||||||||||||||
|
X0 |
|||||||||||||||||||||
|
↓ |
4 |
↓ |
|||||||||||||||||||
|
S WX0 0 0 |
0 |
0 |
0 |
1 |
0 |
0 |
0 |
1 |
0 |
0 |
|||||||||||
ØX0=•
|
D |
R1 |
B15 |
0 |
0 |
0 |
1 |
0 |
0 |
1 |
1 |
0 |
1 |
0 |
0 |
1 |
B0 |
|
↓ |
↓ |
|||||||||||||||
|
0 0 |
0 |
Tip: press ← → to switch chapters, Ctrl+K to search
Operand 













Operand 



















Operand 


Operand 



Operand
Ladder symbol
Operand 
Operand
Operand 









Operand 







Operand 





























TMR







Operand 






Operand 











Operand 























Operand 
















Operand 









