{"id":3413,"date":"2026-11-17T21:34:25","date_gmt":"2026-11-17T13:34:25","guid":{"rendered":"https:\/\/resource.fatek.com\/index.php\/2026\/11\/17\/fbs-hw-en-007\/"},"modified":"2026-11-17T21:34:25","modified_gmt":"2026-11-17T13:34:25","slug":"fbs-hw-en-007","status":"publish","type":"post","link":"https:\/\/resource.fatek.com\/index.php\/2026\/11\/17\/fbs-hw-en-007\/","title":{"rendered":"Chapter 7 Digital Output (DO) Circuit"},"content":{"rendered":"<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-001.png\" \/><\/p>\n<p>The digital outputs of FBS-PLC are available in the following two structures: the 5VDC ultra high speed Line-driver type differential output (i.e., one output occupying two terminals), and the single-end output circuit for saving terminals. There are three kinds of output device for the single-end output, which are relays, TRIAC and transistors. Since the relay and TRIAC are bilateral, even when used in single-end output, they can serve as SINK or SOURCE output. The transistor, however, because of its polarities, after being used as single-end common output, its SINK and SOURCE polarities are exactly the opposite (common point Cn of SINK output must connect to negative end of DC power). Therefore, the product model of transistor output of FBS-PLC for SINK and SOURCE is distinct. At the right side of terminal block of FBS-PLC, there is a place for making SINK or SOURCE label. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<tr>\n<td><\/td>\n<td colspan=\"2\" rowspan=\"3\">\n<p>\u2022Warning<\/p>\n<p>over current protection is available in the FBS series PLC. Except for the 5V differential output circuit, all er output circuits have to be added with over current or short circuit protections externally, such as fuses, in a pplications with safety concern. <\/p>\n<p>\tminals labeled by\u301d\u25cf\u301eon the terminal block are empty contacts, which cannot be connected with any wire to maintain the required safety clearance and to avoid damage to the unit. <\/p>\n<p>ituations where simultaneous operations of outputs(such as reverse\/forward action of motor) pose safety cerns, besides the interlock in PLC programs, additional interlock circuits are needed outside PLC, as shown below\uff1a<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>PLC <br \/>Forward  PLC<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>Forward \u6b63\u8f49\u6975<\/p>\n<p>limit switch<\/p>\n<p>\u9650\u958b\u95dc<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>Interlock \u4e92\u9396\u63a5\u9edecontact <\/p>\n<p> (NC) (NC) <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Magnetic<br \/>\u96fb\u78c1\u958b\u95dc\u6216switch or<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>\u6b63\u8f49\u8f38\u51fa<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u7e7c\u96fb\u5668A Relay A <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u8f38\u51faOutput <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>Reverse\u53cd\u8f49\u6975<\/p>\n<p>Limit <\/p>\n<p>\u9650\u958b\u95dcswitch<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>\u4e92\u9396\u63a5\u9edeInterlock <\/p>\n<p>contact <\/p>\n<p> (NC) (NC) <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>\u96fb\u78c1\u958b\u95dc\u6216<br \/>\u7e7c\u96fb\u5668B switch or <br \/>\tRelay B <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u8f38\u51faOutput <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> PLC PLC <\/p>\n<p>Reverse <\/p>\n<p>\u53cd\u8f49\u8f38\u51faoutput <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>No oth <br \/>in a Ter <br \/>to <br \/>In s con sho<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-002.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>7.1Specifications of Digital Output Circuit <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"3\" rowspan=\"6\">\n<p>\t\t Item Specification <br \/>Maximum output <br \/>frequency* <br \/>Working Voltage <\/p>\n<\/td>\n<td colspan=\"3\">\n<p>Differential <\/p>\n<\/td>\n<td colspan=\"14\">\n<p>Single-End Transistor Output <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"4\">\n<p>Output <\/p>\n<\/td>\n<td colspan=\"4\">\n<p>(T, J ) <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>Single-End <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>Ultra High <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>High <\/p>\n<\/td>\n<td colspan=\"3\">\n<p>Medium <\/p>\n<\/td>\n<td colspan=\"5\">\n<p>Low <\/p>\n<\/td>\n<td colspan=\"4\">\n<p> Relay Output<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Speed <\/p>\n<\/td>\n<td colspan=\"4\">\n<p>Speed <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Speed <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>Speed <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>920KHz <\/p>\n<\/td>\n<td colspan=\"4\">\n<p>200KHz<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>20KHz <\/p>\n<\/td>\n<td>\n<p>\u2500<\/p>\n<\/td>\n<td colspan=\"8\">\n<p>For ON\/OFF, not for frequent exchange <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"4\">\n<p>5VDC\u00b110% <\/p>\n<\/td>\n<td colspan=\"4\">\n<p>5\uff5e30VDC <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>&lt;250VAC, 30VDC<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\" rowspan=\"4\">\n<p>Maximum Load <br \/>Current <\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>Resistive Inductive <\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"5\">\n<p>50mA <\/p>\n<\/td>\n<td colspan=\"4\" rowspan=\"5\">\n<p>0.5A <\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"5\">\n<p>0.5A <\/p>\n<\/td>\n<td colspan=\"4\">\n<p>0.5A <\/p>\n<\/td>\n<td colspan=\"5\" rowspan=\"2\">\n<p>2A\/single, 4A\/common<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"4\" rowspan=\"2\">\n<p>0.1A <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"5\" rowspan=\"3\">\n<p>80VA(AC)\/24VA(DC)<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"4\" rowspan=\"2\">\n<p>(24YT\/J)<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\" rowspan=\"4\">\n<p>Maximum Voltage <br \/>Drop\/conducing resistance <\/p>\n<p>Minimum Load <\/p>\n<p>Leakage Current <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\uff0d<\/p>\n<\/td>\n<td colspan=\"5\">\n<p>0.6V <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>2.2V <\/p>\n<\/td>\n<td colspan=\"6\">\n<p>2.2V <\/p>\n<\/td>\n<td colspan=\"3\">\n<p>0.06V(initial)<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\uff0d<\/p>\n<\/td>\n<td colspan=\"7\">\n<p>\uff0d<\/p>\n<\/td>\n<td colspan=\"9\">\n<p>2mA\/DC power<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\uff0d<\/p>\n<\/td>\n<td colspan=\"15\">\n<p>\uff1c0.1 mA\/30VDC <\/p>\n<\/td>\n<td>\n<p>\uff0d<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Maximum Output <br \/>Delay <br \/>Time <\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"2\">\n<p>ON\u2192OFF OFF\u2192ON <\/p>\n<\/td>\n<td colspan=\"17\">\n<p>15\u03bcS <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>200nS <\/p>\n<\/td>\n<td colspan=\"5\">\n<p>2\u03bcS <\/p>\n<\/td>\n<td colspan=\"6\">\n<p>30\u03bcS <\/p>\n<\/td>\n<td colspan=\"4\">\n<p>10mS<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\" rowspan=\"21\">\n<p>Output Status Indication Over Current Protection <\/p>\n<p>Isolation Type <\/p>\n<p>SINK\/SOURCE Output Type <\/p>\n<p>FBS-20MNR\/T\/J <br \/>FBS-32MNR\/T\/J <br \/>FBS-44MNR\/T\/J <br \/>FBS-10MCR\/T\/J <br \/>FBS-14MCR\/T\/J <br \/>FBS-20MCR\/T\/J <br \/>FBS-24MCR\/T\/J <br \/>FBS-32MCR\/T\/J <br \/>FBS-40MCR\/T\/J <br \/>FBS-60MCR\/T\/J <br \/>FBS-10MAR\/T\/J <br \/>FBS-14MAR\/T\/J <br \/>FBS-20MAR\/T\/J <br \/>FBS-24MAR\/T\/J <br \/>FBS-32MAR\/T\/J <br \/>FBS-40MAR\/T\/J <br \/>FBS-60MAR\/T\/J <br \/>Expansion <br \/>Units\/Modules(R\/T\/J) <\/p>\n<\/td>\n<td colspan=\"17\">\n<p>LED is bit when\u301dON\u301e, dark when\u301dOFF\u301e<br \/>N\/A <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"11\">\n<p>Photocoupler Isolation, 500VAC, 1 minute <\/p>\n<\/td>\n<td colspan=\"6\">\n<p>Electromagnetic Isolation, 1500VAC, 1 minute<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>Independent <\/p>\n<\/td>\n<td colspan=\"7\" rowspan=\"2\">\n<p>Choose SINK\/SOURCE by models and non-exchangeable <\/p>\n<\/td>\n<td colspan=\"7\" rowspan=\"2\">\n<p>Bilateral device, can be arbitrarily set to SINK\/SOURCE output <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>Dual Terminals for arbitrary <br \/>connection <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Y0~1 <\/p>\n<\/td>\n<td colspan=\"6\">\n<p>Y2~7 <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>Y2~7 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Y0~3 <\/p>\n<\/td>\n<td colspan=\"6\">\n<p>Y4~7 <\/p>\n<\/td>\n<td colspan=\"7\">\n<p>Y8~11 <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Y4~11 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"8\">\n<p>Y0~7 <\/p>\n<\/td>\n<td colspan=\"7\">\n<p>Y8~15 <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Y8~15 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"6\">\n<p>Y0,1 <\/p>\n<\/td>\n<td colspan=\"11\">\n<p>Y2,3 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"6\">\n<p>Y0,1 <\/p>\n<\/td>\n<td colspan=\"11\">\n<p>Y2~5 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"6\">\n<p>Y0~3 <\/p>\n<\/td>\n<td colspan=\"11\">\n<p>Y4~7 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"6\">\n<p>Y0~3 <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Y4~7 <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>Y8~9 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"6\">\n<p>Y0~5 <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Y6,7 <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>Y8~11 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"6\">\n<p>Y0~5 <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Y6,7 <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>Y8~15 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"8\">\n<p>Y0~7 <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>Y8~23 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"8\">\n<p>Y0~3 <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>All output points <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"17\">\n<p>Y0~5 <br \/>Y0~7 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"8\">\n<p>Y0~7 <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>Y8,9 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"8\">\n<p>Y0~7 <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>Y8~11 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"8\">\n<p>Y0~7 <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>Y8~15 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"8\">\n<p>Y0~7 <\/p>\n<\/td>\n<td colspan=\"9\">\n<p>Y8~23 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"17\">\n<p>All output <br \/>points <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>*Half of the maximum frequency while A\/B phase output <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-003.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>7.25VDC Ultra High Speed Line-Driver Differential Output Circuit and its Wiring <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>The 5VDC ultra high speed Line-Driver differential output circuit of FBS-PLC is only available for the main unit of the MN model. Its output can connect to general photo coupler circuit or Line-Receiver input circuit, with the connection shown in the figure below. To improve noise immunity and maintain signal quality, please use twisted pair with shield (or aluminum foils) for connection and connect the shield with SG of PLC and FG of the driver. Please also operate in 2-phase driving mode (because 2-phase driving can automatically cancel interferences from noise pulses). <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FBS-MN Main Unit <br \/>\t\tFBS-MN \u4e3b\u6a5f<br \/>\tFB S-XXMN <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>Twisted-pair \u96d9\u7d5e\u7dda<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>\tLoad <br \/>\u8ca0\u8f09<\/p>\n<\/td>\n<td>\n<p>Photocouple <br \/>Photocouple input \u8f38\u5165\u4e4b\u7bc4\u4f8b<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Line-Driver Line-Driver<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Line-Receiver <br \/>Line-Receiver input \u8f38\u5165\u4e4b\u7bc4\u4f8b<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Output \u8f38         \u51fa<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>With frequency up to 920KHz, for high speed or high noise environments<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>7.3Single-End Output Circuit <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Except that the 5VDC ultra high speed output circuit has independent dual terminal outputs, all other output circuits such as relays, transistors or TRIAC are single-end output structure. A single-end output in each digital output (DO) takes up only one terminal. But since any output device has two ends, the one end of several output devices have to be connected together to one common point (called output common) for single-end output. Then each output point can output via this common point. The more output device share a same common points, the more terminals are saved, while relatively increasing the current running through the common point. Combination of any output common with its individual single-end outputs are called a Common Output Block, which is available in 2, 4 and 8PTs (high-density module) in FBS-PLC. Each Common Output Block is separated from one another. The common terminal has a label initiated with letter \u201cC\u201d, while its numbering is determined by the minimum Yn number which comprise the output block. In the example of the figure below, the number of common terminal of output block Y2 and Y3 is C2, while the number of common terminal of output Block Y4, Y5, Y6 and Y7 is C4. The various single-end common output circuits are described below\uff1a<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>7.3.1Structure and Wiring of Single-End Relay Output Circuit <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Because relay contacts have no polarity, it can be applied for AC or DC load power. Each relay can provide current up to 2A. The maximum rated current in all output commons of FBS-PLC is 4A. Its mechanical lifetime can reach up to 2 million times, while the contacts have a shorter lifetime. The lifetime also varies depending on working voltage, load type (power factor cos\u03c8) and contact current. The relation between them is plotted in the figure below. In the case of pure resistive load (cos\u03c8=1.0) at 120VAC and 2A, the lifetime of contacts is about 250 thousand times. While for high inductive or capacitive load with cos\u03c8up to 0.2 and current within 1A, the lifetime decreases rapidly to about 50 thousand times (AC200V) or 80 thousand times (AC120V). <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-004.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-005.png\" \/><\/p>\n<p>FBS-PLC <\/p>\n<p> AC\/DC AC\/DC  AC\/DC AC\/DC <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"9\">\n<p> \u96fb\u6e90power <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>4A <\/p>\n<\/td>\n<td>\n<p> \u96fb\u6e90power<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>4A<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>FUSE <\/p>\n<\/td>\n<td>\n<p>FUSE<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u52d5<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-006.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u4f5c<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u6b21<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u6578<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u842c<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u6b21<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u63a5\u9ede\u96fb\u6d41(A)<\/p>\n<p>Contact Current (A) <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>7.3.2Structure and Wiring of Single-End Transistor SINK and SOURCE Output Circuit <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>A. <\/p>\n<\/td>\n<td>\n<p>Transistor Single-End SINK Output <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>FBS-PLC<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>C2<\/p>\n<\/td>\n<td>\n<p> 1A<\/p>\n<\/td>\n<td>\n<p>Y2<\/p>\n<\/td>\n<td>\n<p>Y3<\/p>\n<\/td>\n<td>\n<p>C4<\/p>\n<\/td>\n<td>\n<p>2A<\/p>\n<\/td>\n<td>\n<p>Y4<\/p>\n<\/td>\n<td>\n<p>Y5<\/p>\n<\/td>\n<td>\n<p>Y6<\/p>\n<\/td>\n<td>\n<p>Y7<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>FUSE FUSE<\/p>\n<p>2PTs Common Output Block <\/p>\n<p>4PTs Common Output Block <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-007.png\" \/><\/p>\n<p>B. Transistor Single-End SOURCE Output<\/p>\n<p>FBS-PLC<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> 1A<\/p>\n<\/td>\n<td>\n<p>2A<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>C4<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Y4<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Y5<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Y7<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>FUSE<\/p>\n<\/td>\n<td>\n<p>FUSE<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>DC <br \/>power<\/p>\n<p>2PTs Common Output Block \t4PTs Common Output Block <\/p>\n<p>The figure above uses output block s of 2PTs common and 4PTs common as an example to explain the differences in structural and wiring for SINK and SOURCE output circuits, respectively.(8PTs common has the same block structure and wiring, except with different point number) The single-end SINK output and SOURCE transistor output in FBS-PLC are different models. The user must check whether it is SINK output model or SOURCE output model when purchasing. <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-008.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-009.png\" \/><\/p>\n<p>7.4Speed up the Single-End Transistor Output Circuit (only applicable to high and <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>medium-speed) <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Either with the SINK or SOURCE structure in single-end output transistor circuit, when the transistor switches from ON to OFF, the junction capacitor between transistor CE electrodes should be charged to near the load voltage VDD before it can stop the current running through the photocoupler inside the load, which increase the OFF time and decrease the response speed. This problem can be solved by adding a Dummy load to accelerate charging rate and speed up the working frequency of transistor output. For the transistor output in FBS-PLC, Dummy load that are added to the high- and medium-speed transistor output and generate a load current of 20~50mA is adequate. For low speed transistor where its driving capability (0.5A) but speed is concerned, adding a Dummy load only decreases its driving capability without any significant improvement and hence is not recommended. The following diagram shows how to add a Dummy load to SINK and SOURCE transistor output. <\/p>\n<p>FBS-PLC \tFBS-PLC<\/p>\n<p>Load <br \/>Load<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>R<\/p>\n<\/td>\n<td>\n<p>VDD<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>R<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>VDD<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>5~30<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>I<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>VDC<\/p>\n<\/td>\n<td>\n<p>5~30<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>VDC<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>I<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>SINK output<\/p>\n<\/td>\n<td>\n<p>I =<\/p>\n<\/td>\n<td>\n<p>VDD =20~50mA \tR<\/p>\n<\/td>\n<td>\n<p>SRCE output<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>7.5Output Device Protection and Noise Suppression in DO Circuit <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Since the digital output circuits are mainly used for the ON\/OFF switching operation, the output components such as relays, transistors and TRIAC can be deemed as kinds of switch components. Normally, surge currents or counter-electromotive force voltages are generated during the ON\/OFF operation of these switch components. The effect of surge currents or counter-electromotive force voltages is particularly serious when heavy capacitive or inductive loads are incorporated, which may cause damage to the output components or generate noises in other electronic circuits and equipment. Among those three FBS-PLC output components, where TRIAC require no special treatment because of their features of smaller rated current, zero cross in ON\/OFF, and built-in protection circuits, special consideration should be given to relays and transistors when they are used in high power applications or connected with capacitive or inductive loads and are described in the following: <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>7.5.1Protection of Relay Contacts and Noise Suppression <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Because the relay contacts are used to contact switch components having extremely low resistance, the surge current IR generated instantly upon turning on the relay is normally pretty strong (even if the steady load current is very small). Under such strong surge, the contact tends to melt and stick due to extreme temperature in such a way that the relay cannot trip when it is disconnected. In addition, when the relay connections are OFF, large di\/dt is generated because of the instantaneous change from low resistance to open circuit (\u221e) soon after following the tripping of contact. As a result, an extremely strong counter-electromotive force voltage is induced, which creates sparks between the electrodes of two relay contacts and results in poor contact due to carbon deposits. Among those three output components, either in ON or OFF state, very serious interference can be caused by the surge current or the counter-electromotive of the relay. The solutions to this problem are listed as follows: <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-010.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-011.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-012.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-013.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-014.png\" \/><\/p>\n<p>A.Suppression of Surge Current\u4ee5Connect a small resistor R in series to lower the surge current, <\/p>\n<p>but note that too large R will affect the driving capability or cause too much voltage drop. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"2\" rowspan=\"3\">\n<p>Load Load <\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>I r Ir <\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>R<\/p>\n<\/td>\n<td>\n<p>PLC \u8f38\u51faPLC output <\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>\u6e67\u6d6a\u96fb\u6d41\u4f7f\u63a5\u9ede\u7194\u5316\u9ecf\u4f4f<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> \u7e7c\u96fb\u5668relay <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>R<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>I s Is <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Electronic <br \/>\u96fb \u5b50<\/p>\n<p>Circuits <\/p>\n<p>\u96fb \u8def<\/p>\n<\/td>\n<td>\n<p>C<\/p>\n<\/td>\n<td>\n<p>V<\/p>\n<\/td>\n<td>\n<p>VDD<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\t\tVDD <br \/>R\u2267             (note power dissipation P\uff1dIs2R and voltage drop V\uff1dIsR) \t Ir max <\/p>\n<p>Ir max of relay in FBS-PLC \uff1d5A <\/p>\n<p>B.Suppression of Counter-Electromotive Force <\/p>\n<p>For the inductive load, whether in AC or DC power, suppression devices must be connected in parallel to both its <\/p>\n<p>ends to protect the relay contacts and lower noise interference. The schematic diagrams for AC and DC powers are <\/p>\n<p>shown below, respectively: <\/p>\n<p>PLC Relay output <br \/>\tInductive load<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>R<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>R<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>C<\/p>\n<\/td>\n<td>\n<p>R:100~120\u2126 R : 100 ~ 120\u03a9<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>C:0.1~0.24uF C : 0.1 ~ 0.24uF<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Scheme of AC power load <\/p>\n<p>PLC Relay output <br \/>Inductive load<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>R<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>D<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>VDC<\/p>\n<\/td>\n<td>\n<p>D : 1N4001 diode or<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> equivalent device<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Suppress by a diode in DC power load (for low power\uff09<\/p>\n<p>PLC Relay output <br \/>\tInductive load<\/p>\n<p>D : 1N4001 diode or<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>R<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>ZD<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>D<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>VDC<\/p>\n<\/td>\n<td>\n<p> equivalent device<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>ZD : 9V Zener, 5W<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Suppress by a diode + Zener in DC power load (for high power and frequent ON\/OFF) <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-015.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-007\/fbs-hw-en-007-016.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>7.5.2Protection of Transistor Output and Noise Suppression <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>The transistor output in FBS-PLC already includes Zener diode for counter-electromotive force, which is sufficient for low power inductive load and medium frequency of ON\/OFF application. In conditions of high power or frequent ON\/OFF, please construct another suppression circuit to lower noise interference and prevent voltage from exceeding the limit or overheating that may damage the transistor output circuit. <\/p>\n<p>PLC Relay output <br \/>Inductive load<\/p>\n<p>D : 1N4001 diode or<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>D<\/p>\n<\/td>\n<td>\n<p>VDC<\/p>\n<\/td>\n<td>\n<p> equivalent device<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Suppress by a diode (for low power) <\/p>\n<p>PLC Relay output <br \/>\tInductive load<\/p>\n<p>D : 1N4001 diode or<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>ZD<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>D<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>VDC<\/p>\n<\/td>\n<td>\n<p> equivalent device<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>ZD : 9V Zener, 5W<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Suppress by a diode + Zener (high power and frequent ON\/OFF) <\/p>\n","protected":false},"excerpt":{"rendered":"<p>The digital outputs of FBS-PLC are available in the fol [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[33],"tags":[],"class_list":["post-3413","post","type-post","status-publish","format-standard","hentry","category-en-fbs-hw"],"_links":{"self":[{"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/posts\/3413","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/comments?post=3413"}],"version-history":[{"count":0,"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/posts\/3413\/revisions"}],"wp:attachment":[{"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/media?parent=3413"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/categories?post=3413"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/tags?post=3413"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}