{"id":3416,"date":"2026-11-17T21:34:41","date_gmt":"2026-11-17T13:34:41","guid":{"rendered":"https:\/\/resource.fatek.com\/index.php\/2026\/11\/17\/fbs-hw-en-011\/"},"modified":"2026-11-17T21:34:41","modified_gmt":"2026-11-17T13:34:41","slug":"fbs-hw-en-011","status":"publish","type":"post","link":"https:\/\/resource.fatek.com\/index.php\/2026\/11\/17\/fbs-hw-en-011\/","title":{"rendered":"Chapter 11 The NC Positioning Control of FBs-PLC"},"content":{"rendered":"<p>People use ordinary motor to exercise positioning control in early stage; since the speed and precision demand was not so high then, it was enough to fulfill the demand.  As the increasing of mechanical operation speed for the efficiency purpose, finished product quality standard, and precision demands are getting higher, the stopping position control of motor is no more what the ordinary motor is capable to do.  The best solution for this problem is to adopt NC positioning controller which incorporate with stepping or servo motor to do the position control.  In the past, the extremely high cost limited the prevailing of its usage; however, the technology advance and cost decreasing, which made the pricing affordable, had helped to increase the prevailing of usage gradually.  To cope with this trend, the FBs-PLC integrated into its internal SoC chip the special NC positioning controller that is available on the market, therefore makes it free from the bothersome data transaction and linking procedure between PLC and special NC positioning controller. Furthermore, it greatly lowered the entire gadget cost hence provides the user the solution for a good bargain, high quality, simple, and convenient integrated NC positioning control with PLC. <\/p>\n<h3>11.1 The Methods of NC Positioning <\/h3>\n<p>The methods for controlling interface of PLC and stepping or servo driver are as follows: <\/p>\n<p>z Giving command by way of digital I\/O: Easy to use but less dexterity in application. <\/p>\n<p>z Giving command by way of analogue output: Better dexterity in controlling reaction but it is with a higher cost and \teasy to be interfered by noise. <\/p>\n<p>z Giving command by way of communication:  There is no standard for communication protocol and it is confined in \tcommunication reaction thus constitutes a bottleneck for application. <\/p>\n<p>z Giving command by way of high speed pulse:  The cost is low and is easy to precisely controlled. <\/p>\n<p>Of these methods, controlling stepping or servo driver with high speed pulse is more frequently used method.  The main unit of PLC contains multi-axis high speed pulse output and hardware high speed counter, and it can provide easy using, designing for positioning program editing.  Therefore it makes the related application even more convenient and comfortable. <\/p>\n<p>Following two kinds are frequently used NC server system that constituted by PLC associates with servo drivers: <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>z<\/p>\n<\/td>\n<td>\n<p>Semi closed loop control <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>The PLC is responsible for sending high speed pulse command to servo driver.  The motion detector installed on servo motor will forward directly to server driver, closed loop reaches only to server driver and servo motor. The superior point is that the control is simple and the precision is satisfactory (which is suitable for most of the applications).  The defect is that it can\u2019t fully reflect the actual shift amount after the transmission element; furthermore, the element being consumed, become aging, or has defect will not be able to be compensated nor checked to verify. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>z<\/p>\n<\/td>\n<td>\n<p>Closed loop control<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>The PLC is responsible for sending high speed pulse command to servo driver.  In addition to that the shift detection signal installed on servo motor which will be forwarded directly to servo driver, the attached shifting detector installed after the transmission element can fully reflect the actual shift amount and forward it to the high speed counter that PLC contains.  So as to make the control becomes more delicate, and help to avoid the defect of above mentioned semi closed loop. <\/p>\n<h3>11.2 Absolute Coordinate and Relative Coordinate <\/h3>\n<p>\tThe designation of moving distance can be assigned by absolute location (absolute coordinate positioning), or assigned by relative distance (relative coordinate positioning).  And the DRV instruction is used to drive motor. <\/p>\n<p>While marking the moving distance with absolute coordinate, <br \/>if it is located at 100mm at the present, for moving to 300 mm, the positioning instruction is : DRV  ABS,  ,300 , Ut if it is located at 300mm at the present, for moving to 0mm, the positioning instruction is \t: DRV  ABS,  ,  0 , Ut. <\/p>\n<p>While marking the moving distance with relative coordinate, <br \/>if it is located at 100mm at the present, for moving to 300 mm, the positioning instruction is : DRV  ADR, +, 200, Ut. if it is located at 300mm at the present, for moving to 0mm, the positioning instruction is \t: DRV  ADR, \u2212, 300, Ut. <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-001.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-002.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-003.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-004.png\" \/><\/p>\n<p>z Absolute coordinate labeling <br \/>\tProgram coding for location of 300mm moving to 0mm: <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-005.png\" \/><\/p>\n<p>DRVABS,,  0,Ut<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>\uff0e\uff0e\uff0e<\/p>\n<\/td>\n<td colspan=\"5\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<td rowspan=\"2\">\n<p>\uff0e\uff0e\uff0e<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>-100 <\/p>\n<\/td>\n<td>\n<p>0 <\/p>\n<\/td>\n<td>\n<p>100 <\/p>\n<\/td>\n<td>\n<p>200 <\/p>\n<\/td>\n<td>\n<p>300 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-006.png\" \/><\/p>\n<p>\t Program coding for location of 100mm moving to 300mm: \t\t\tDRVABS,,300,Ut <br \/>z Relative coordinate labeling <br \/>\tProgram coding for location of 300mm moving to 0mm: <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-007.png\" \/><\/p>\n<p>DRV  ADR,\uff0d,300,Ut<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>\uff0e\uff0e\uff0e<\/p>\n<\/td>\n<td colspan=\"5\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<td rowspan=\"2\">\n<p>\uff0e\uff0e\uff0e<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>-100 <\/p>\n<\/td>\n<td>\n<p>0 <\/p>\n<\/td>\n<td>\n<p>100 <\/p>\n<\/td>\n<td>\n<p>200 <\/p>\n<\/td>\n<td>\n<p>300 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-008.png\" \/><\/p>\n<p> Program coding for location of 100mm moving to 300mm: <br \/>\tDRV  ADR,+,200,Ut <\/p>\n<h3>11.3 Procedures of Using FBs-PLC Positioning Control <\/h3>\n<p>Start <\/p>\n<p>Configure the high speed pulse output (HSPSO) function under WinProladder or FP-08 configuration function.  Switch <\/p>\n<p>the Y0\uff5eY7 output of FBs-PLC to HSPSO circuit in the SoC, <\/p>\n<p>and determine the working mode of output pulse (U\/D, PLS\/DIR, A\/B), and complete the hardware wiring layout between PLC and positioning driver. <\/p>\n<p>&#8212;&#8212;For the wiring layout, please refer to section 11.4.2. <\/p>\n<p>Each axis of motor is controlled by one FUN140 (it can also by <\/p>\n<p>more than one, but only one can be active at any time); then employs the FUN140 extended positioning instruction (SPD, <\/p>\n<p>Please refer to FUN140 and its extended <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>DRV,\u2026 etc.) to coding for the needed positioning control <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>&#8212;&#8212;<\/p>\n<\/td>\n<td>\n<p>positioning instruction for the function and usage <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>program that will be saved into register block assigned by <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>explanation. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>FUN140 SR operand.  Once the FUN 140 input control <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>started, it can exercise the positioning controls. <\/p>\n<p>If it needs to do close loop control, it can employ the FBs-PLC hardware high speed counter to count the feedback pulse (e.g. Encoder etc.) after transmission element to achieve. <\/p>\n<p>End <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-009.png\" \/><\/p>\n<h3>11.4 Explanation for the Positioning Control Hardware of FBs-PLC <\/h3>\n<h4>11.4.1 Structure of Output Circuit of HSPSO<\/h4>\n<p>According to different main unit, it provides different frequency of output pulse, it includes 20KHz (Medium speed) of single ended transistor output model (FBS-xxMCT), and high speed differential output model (FBS-xxMNT) which can reach 920KHz (for single phase), two series of models. <\/p>\n<p>High speed pulse output circuit share to use the Y0\uff5eY7 exterior output of FBs-PLC.  While it is not yet using the HSPSO function (haven\u2019t configured the PSO function under configuration function), the Y0\uff5eY7 exterior output of FBs-PLC is corresponding to the Y0\uff5eY7 status of internal output relay.  When the HSPSO has been configured, the Y0\uff5eY7 exterior output will switch directly to HSPSO output circuit within SoC, which has no relation with Y0\uff5eY7 relay inside PLC. <\/p>\n<p>The following is the detailed signals list for respective axis output of main unit and the selectable output modes: <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>Axis No. <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Exterior output <\/p>\n<\/td>\n<td colspan=\"4\">\n<p>Output modes <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>U\/D output <\/p>\n<\/td>\n<td>\n<p>P\/R output <\/p>\n<\/td>\n<td>\n<p>A\/B output <\/p>\n<\/td>\n<td>\n<p>Single PLS output <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>PSO0 <\/p>\n<\/td>\n<td>\n<p>Y0 , Y1 <\/p>\n<\/td>\n<td>\n<p>Y0=U , Y1=D <\/p>\n<\/td>\n<td>\n<p>Y0=P , Y1=R <\/p>\n<\/td>\n<td>\n<p>Y0=A , Y1=B <\/p>\n<\/td>\n<td>\n<p> Y0=PLS <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>PSO1 <\/p>\n<\/td>\n<td>\n<p>Y2 , Y3 <\/p>\n<\/td>\n<td>\n<p>Y2=U , Y3=D <\/p>\n<\/td>\n<td>\n<p>Y2=P , Y3=R <\/p>\n<\/td>\n<td>\n<p>Y2=A , Y3=B <\/p>\n<\/td>\n<td>\n<p> Y2=PLS <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>PSO2 <\/p>\n<\/td>\n<td>\n<p>Y4 , Y5 <\/p>\n<\/td>\n<td>\n<p>Y4=U , Y5=D <\/p>\n<\/td>\n<td>\n<p>Y4=P , Y5=R <\/p>\n<\/td>\n<td>\n<p>Y4=A , Y5=B <\/p>\n<\/td>\n<td>\n<p> Y4=PLS <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>PSO3 <\/p>\n<\/td>\n<td>\n<p>Y6 , Y7 <\/p>\n<\/td>\n<td>\n<p>Y6=U , Y7=D <\/p>\n<\/td>\n<td>\n<p>Y6=P , Y7=R <\/p>\n<\/td>\n<td>\n<p>Y6=A , Y7=B <\/p>\n<\/td>\n<td>\n<p> Y6=PLS <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<h4>11.4.2 Hardware Wiring Layout for FBs-PLC Positioning Control <\/h4>\n<p>\t Take the 0th axis (PSO0) of FBs-XXMCT, FBs-XXMAT, and FBs-XXMNR(T) main unit for example, it is illustrated with diagrams as follows; the others are the same. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"2\"><\/td>\n<\/tr>\n<tr>\n<td>\n<p>A, FBS-XXMCT , FBs-XXMAT single ended output wiring layout.<\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"3\">\n<p>FBs main unit<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>Y0<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>*R<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>R<\/p>\n<\/td>\n<td colspan=\"3\">\n<p>Driver (photocouple input)<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>+<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>A+<\/p>\n<\/td>\n<td>\n<p>A phase<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>A-<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>(or U or PLS)<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>5~24V DC<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>Y1<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>*R<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>R<\/p>\n<\/td>\n<td>\n<p>B+<\/p>\n<\/td>\n<td>\n<p>B phase<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>External power supply<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>B-<\/p>\n<\/td>\n<td>\n<p>(or D or DIR)<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>C0<\/p>\n<p>\uff0a Please refer to Hardware manual H7-6 for the usage of speed-up resistor \u201cR\u201d. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-010.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-011.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-012.png\" \/><\/p>\n<p>Driver (OP input)<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"5\">\n<p>FBs main unit<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>Y0<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>*R<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>*R<\/p>\n<\/td>\n<td>\n<p>Va<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>A phase<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>+<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>A<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>5~24V DC<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>(or U or PLS)<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Y1<\/p>\n<\/td>\n<td>\n<p>B<\/p>\n<\/td>\n<td>\n<p>B phase<\/p>\n<\/td>\n<td>\n<p>External power supply<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>(or D or DIR)<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>C0<\/p>\n<\/td>\n<td>\n<p>C<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<td>\n<p>B\u3001FBS-XXMNR(T) differential output wiring layout <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>FBS-XXMN PLC<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Y0+<\/p>\n<\/td>\n<td rowspan=\"9\">\n<p>Twisted pair<\/p>\n<\/td>\n<td>\n<p>Driver (Photocouple input)<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>A+<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Y0<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Y0-<\/p>\n<\/td>\n<td>\n<p>A phase(or U or PLS)<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>A-<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>Y1<\/p>\n<\/td>\n<td>\n<p>SG<\/p>\n<\/td>\n<td>\n<p>FG<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Y1+<\/p>\n<\/td>\n<td>\n<p>B+<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>B phase(or D or DIR)<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>FBS-XXMN PLC<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Y1-<\/p>\n<\/td>\n<td>\n<p>B-<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Driver (Line receiver input)<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Y0<\/p>\n<\/td>\n<td>\n<p>Y0+<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>Twisted pair<\/p>\n<\/td>\n<td>\n<p>A+<\/p>\n<\/td>\n<td>\n<p>A phase(or U or PLS)<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"4\">\n<p>Y1<\/p>\n<\/td>\n<td>\n<p>Y0-<\/p>\n<\/td>\n<td>\n<p>A-<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>B phase(or D or DIR)<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>SG<\/p>\n<\/td>\n<td>\n<p>FG<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Y1+<\/p>\n<\/td>\n<td>\n<p>B+<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Y1-<\/p>\n<\/td>\n<td>\n<p>B-<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\uff08For line receiver input, it must make PLC connect to FG of driver to eliminate common mode voltage\uff09<\/p>\n<p> Configuration of HSPSO with WinProladder <\/p>\n<p> Click the \u201cI\/O Configuration\u201d Item which in project windows<strong> :<\/strong><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> Project name  <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<tr>\n<td><\/td>\n<td>\n<p> System C<\/p>\n<\/td>\n<td>\n<p>nfiguratio<\/p>\n<\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\"><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<tr>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<tr>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> I\/O Configuration  \u00c6 select  \u201cOutput Setup\u201d <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>When \u201cOutput Setup\u201d windows appear, then you can configure the Output type <strong>:<\/strong><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-013.png\" \/><\/p>\n<h3>11.5 The Explanation for the Position Control Function of FBs-PLC <\/h3>\n<p>The position control function of FBs-PLC incorporates the dedicated NC position controller, which is available in the market, into the PLC.  This makes the PLC and NC controller be able to share the same data block without the demand of complicated works like data exchange and synchronized controlling between these two systems.  And it can still use the usual NC positioning control instruction (e.g. SPD , DRV,\u2026 etc.). <\/p>\n<p>One main unit can control up to 4 axes of their position control, and can drive multi axis simultaneously.  However, it provides point to point positioning and speed control, but also it provides the linear interpolation function.  When the system is applying for more than 4 axes, it can also employ CPU LINK function of FBs-PLC to attain control over more positioning actions. <\/p>\n<p>The NC position control instruction for FBs-XXMCT\u3001FBs-XXMN main units are identical to each other. The difference is only on the different circuit output, as previously revealed.  Hereby we assume that FBs-XXMCT main unit is used in the control of stepping motor or server with lower speed, and FBs-XXMN main unit is used in high speed servo motor control.  Consequently, we illustrate only with the connecting diagram of FBs-XXMCT main unit that driving stepping motor and the diagram of FBs-XXMN main unit that driving servo motor.  Of course we can also use FBs-XXMCT main unit to drive servo motor or use FBs-XXMN main unit to drive stepping motor instead, they can still work perfectly, as long as its circuit structure (single ended or differential) and frequency can match. <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-014.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-015.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-016.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-017.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-018.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-019.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-020.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-021.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-022.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-023.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-024.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-025.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-026.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-027.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-028.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-029.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-030.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-031.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-032.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-033.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-034.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-035.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-036.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-037.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-038.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-039.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-040.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-041.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-042.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-043.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-044.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-045.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-046.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-047.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-048.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-049.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-050.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-051.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-052.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-053.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-054.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-055.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-056.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-057.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-058.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-059.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-060.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-061.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-062.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-063.png\" \/><\/p>\n<h4>11.5.1 Interface of Stepping Motor <\/h4>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-064.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-065.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-066.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-067.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-068.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-069.png\" \/><\/p>\n<p>z Stepping motor is designed to receive input pulse to attain to the control of desired angle or distance, therefore the turning angle and the input pulse count has a positive correlation ship, and the turning speed also depends on the input pulse frequency. <\/p>\n<p>N <strong>:<\/strong> Revolving speed of motor (RPM) <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>N (RPM) = 60 \u00d7 f \/ n <\/p>\n<\/td>\n<td>\n<p>f <\/p>\n<\/td>\n<td>\n<p><strong>: <\/strong>Pulse frequency (PLS\/Sec) <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\tn <strong>: <\/strong>Pulse counts for motor to turn for a revolution (PLS\/ Rev). n = 360 \/ \u03b8s \t\u03b8s <strong>:<\/strong> Angle (Deg) <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>Phase <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Basic <br \/>pulse angle <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>FULL <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>HALF <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Pulse angle <\/p>\n<\/td>\n<td>\n<p>Pulse counts for <br \/>turning one revolution<\/p>\n<\/td>\n<td>\n<p>Pulse angle <\/p>\n<\/td>\n<td>\n<p>Pulse counts for <br \/>turning one revolution<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>5 phase <\/p>\n<\/td>\n<td>\n<p>0.36\u00b0<\/p>\n<\/td>\n<td>\n<p>0.36\u00b0<\/p>\n<\/td>\n<td>\n<p>1000 <\/p>\n<\/td>\n<td>\n<p>0.18\u00b0<\/p>\n<\/td>\n<td>\n<p>2000 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>0.72\u00b0<\/p>\n<\/td>\n<td>\n<p>0.72\u00b0<\/p>\n<\/td>\n<td>\n<p>500 <\/p>\n<\/td>\n<td>\n<p>0.36\u00b0<\/p>\n<\/td>\n<td>\n<p>1000 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>4 phase <\/p>\n<\/td>\n<td>\n<p>0.90\u00b0<\/p>\n<\/td>\n<td>\n<p>0.90\u00b0<\/p>\n<\/td>\n<td>\n<p>400 <\/p>\n<\/td>\n<td>\n<p>0.45\u00b0<\/p>\n<\/td>\n<td>\n<p>800 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>2 phase <\/p>\n<\/td>\n<td>\n<p>1.80\u00b0<\/p>\n<\/td>\n<td>\n<p>1.80\u00b0<\/p>\n<\/td>\n<td>\n<p>200 <\/p>\n<\/td>\n<td>\n<p>0.90\u00b0<\/p>\n<\/td>\n<td>\n<p>400 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-070.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-071.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-072.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-073.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-074.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-075.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-076.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-077.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-078.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-079.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-080.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-081.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-082.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-083.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-084.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-085.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-086.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-087.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-088.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-089.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-090.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-091.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-092.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-093.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-094.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-095.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-096.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-097.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-098.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-099.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-100.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-101.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-102.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-103.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-104.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-105.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-106.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-107.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-108.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-109.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-110.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-111.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-112.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-113.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-114.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-115.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-116.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-117.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-118.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-119.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-120.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-121.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-122.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-123.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-124.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-125.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-126.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-127.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-128.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-129.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-130.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-131.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-132.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-133.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-134.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-135.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-136.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-137.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-138.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-139.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-140.png\" \/><\/p>\n<h4>11.5.2 Interface of Servo Motor <\/h4>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-141.png\" \/><\/p>\n<\/td>\n<td><\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-142.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-143.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-144.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-145.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u203b Except that the Y0\uff5eY7 of above diagram are for dedicated purpose, Y8\uff5eY11 and respective inputs can be \tadjusted for using according to demand. <\/p>\n<p>\u203b The left over travel, right over travel limit switches for safety detection also need to be connected to PLC to \tassure proper operation. <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-146.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-147.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-148.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-149.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-150.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-151.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-152.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-153.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-154.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-155.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-156.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-157.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-158.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-159.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-160.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-161.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-162.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-163.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-164.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-165.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-166.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-167.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-168.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-169.png\" \/><\/p>\n<h4>11.5.3  Working Diagram Illustration for Servo Motor<\/h4>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-170.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-171.png\" \/><\/p>\n<p>z The Encoder of servo motor feedback the shifting detection signal to servo driver.  The driver gets the pulse frequency, and pulse count of input signal (pulse command), as well as the frequency and pulse count of feedback signal processed with internal error counter and frequency to voltage conversion circuit, and acquired the pulse and turning speed deviations.  Using these operations to control the servo motor, so as to obtain a high speed, precise speed and positional closed-loop processing system. <\/p>\n<p>z The revolving speed of servo motor depends on the pulse frequency of input signal; the turning stroke of motor is determined by pulse count. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>z<\/p>\n<\/td>\n<td>\n<p>Generally speaking, the final control error deviation of servo motor is \u00b11 pulse. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<h3>11.6 Explanation of Function for NC Position Control Instruction <\/h3>\n<p>The NC position control of FBs-PLC has following four related instructions: <\/p>\n<p>z FUN140 (HSPSO) high speed pulse output instruction, which includes following 9 extension positioning \tinstructions: <\/p>\n<p>2. DRV       5. WAIT 3. DRVC      6. ACT \t8. GOTO \t9. MEND \t<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-172.png\" \/>\tstored to SR operand area of FUN140 1. SPD       4. DRVZ \t7. EXT \t\tUsed for positioning program coding and <\/p>\n<p>z FUN141 (MPARA) positioning parameter setting instruction <\/p>\n<p>z FUN142 (PSOFF) enforcing pulse output stop instruction. <\/p>\n<p>z FUN143 (PSCNV) converting the current pulse value to displaying value instruction. <\/p>\n<p>z FUN147\uff08MHSPO\uff09multi high speed pulse output instruction, which includes following 7 extension positioning \tinstructions: <\/p>\n<p>2. LIN        5. EXT 3. LINE       6. GOTO \t\t<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-173.png\" \/>\tto SR operand area of FUN147 <br \/>1. SPD       4. WAIT \t7. MEND \t\tUsed for positioning program coding and stored <\/p>\n<p>The following function explanations are for the above mentioned 5 instructions: <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-174.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-175.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-176.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-177.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-178.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-179.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-180.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-181.png\" \/><\/p>\n<p>NC Positioning Control Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<td>\n<p>High Speed Pulse Output <br \/>(Including the extended positioning instruction) <\/p>\n<\/td>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>Ps: The set number of Pulse Output (0\uff5e3) <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"3\"><\/td>\n<td rowspan=\"3\"><\/td>\n<td rowspan=\"3\"><\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-182.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-183.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-184.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\"><\/td>\n<td rowspan=\"3\"><\/td>\n<td colspan=\"3\" rowspan=\"5\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-185.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-186.png\" \/><\/p>\n<\/td>\n<td colspan=\"3\">\n<p>0:Y0 &amp; Y1 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\"><\/td>\n<td colspan=\"3\">\n<p>1:Y2 &amp; Y3 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\" rowspan=\"2\">\n<p>2:Y4 &amp; Y5 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\"><\/td>\n<td rowspan=\"15\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-187.png\" \/><\/p>\n<\/td>\n<td rowspan=\"15\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-188.png\" \/><\/p>\n<\/td>\n<td rowspan=\"15\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<td rowspan=\"8\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-189.png\" \/><\/p>\n<\/td>\n<td rowspan=\"8\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-190.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\" rowspan=\"2\">\n<p>3:Y6 &amp; Y7 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-191.png\" \/><\/p>\n<\/td>\n<td colspan=\"3\" rowspan=\"6\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-192.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>SR: Starting register for positioning program <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>(example explanation) <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"10\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-193.png\" \/><\/p>\n<\/td>\n<td colspan=\"3\">\n<p>WR: Starting register for instruction operation (example <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>explanation).  It controls 7 registers, which the other <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>program cannot repeat in using.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"4\">\n<p>Range<\/p>\n<\/td>\n<td>\n<p>HR<\/p>\n<\/td>\n<td>\n<p>DR<\/p>\n<\/td>\n<td>\n<p>ROR<\/p>\n<\/td>\n<td>\n<p>K <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"5\">\n<p>R0 <\/p>\n<\/td>\n<td>\n<p>D0 <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>R5000<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Ope- <\/p>\n<\/td>\n<td colspan=\"3\">\n<p>\u2223<\/p>\n<\/td>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u2223<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>rand <\/p>\n<\/td>\n<td colspan=\"3\">\n<p>R3839<\/p>\n<\/td>\n<td>\n<p>D3999<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>R8071<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"5\">\n<p>Ps <\/p>\n<\/td>\n<td colspan=\"3\">\n<p>0\uff5e3<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>SR <\/p>\n<\/td>\n<td colspan=\"3\">\n<p>\u25cb<\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u25cb<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>WR <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u25cb<\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u25cb*<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p> Instruction Explanation <\/p>\n<p>1. The NC positioning program of FUN140 (HSPSO) instruction is a program written and edited with text programming.  We named every position point as a step (which includes output frequency, traveling distance, and transfer conditions).  For one FUN140, it can be arranged with 250 steps of positioning points at the most, with every step of positioning point controlled by 9 registers. <\/p>\n<p>2. The best benefit to store the positioning program into the registers is that in the case of association with MMI (Man Machine Interface) to operate settings, it may save and reload the positioning program via MMI when replacing the molds. <\/p>\n<p>3. When execution control \u201cEN\u201d=1, if the other FUN140 instructions to control Ps0 \uff5e3 are not active (corresponding status of Ps0=M1992, Ps1=M1993, Ps2=M1994, and Ps3=M1995 will be ON), it will start to execute from the next step of positioning point (when goes to the last step, it will be restarted from the first step to perform); if Ps0\uff5e3 is controlled by other FUN140 instruction (corresponding status of Ps0=M1992, Ps1=M1993, Ps2=M1994, and Ps3=M1995 would be OFF), this instruction will acquire the pulse output right of positioning control once the controlling FUN140 has released the control right. <\/p>\n<p>4. When execution control input \u201cEN\u201d =0, it stops the pulse output immediately. <\/p>\n<p>5. When output pause \u201cPAU\u201d =1 and execution control \u201cEN\u201d was 1 beforehand, it will pause the pulse output. \tWhen output pause \u201cPAU\u201d =0 and execution control is still 1, it will continue the unfinished pulse output. <\/p>\n<p>6. When output abort \u201cABT\u201d=1, it stops pulse output immediately.  (When the execution control input \u201cEN\u201d \tbecomes 1 next time, it will restart from the first step of positioning point to execute.) <\/p>\n<p>7. While the pulse is in output transmitting, the output indication \u201cACT\u201d is ON. <\/p>\n<p>8. When there is execution error, the output indication \u201cERR\u201d will be ON. \t(The error code is stored in the error code register.) <\/p>\n<p>9. When each step of positioning point is complete, the output indication \u201cDN\u201d will be ON. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>NC Positioning Control Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<td>\n<p>High Speed Pulse Output <br \/>(Including the extended positioning instruction) <\/p>\n<\/td>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>***  The working mode of Pulse Output must be set (without setting, Y0\uff5eY7 will be treated as general output) to <\/p>\n<p>be one of U\/D, P\/R, or A\/B mode, thus the Pulse Output may have a regular output. <\/p>\n<p>U\/D Mode <strong>:<\/strong> Y0 (Y2, Y4, Y6), it sends out upward counting pulse. <\/p>\n<p> Y1 (Y3, Y5, Y7), it sends out downward counting pulse. <\/p>\n<p>P\/R Mode<strong> :<\/strong> Y0 (Y2, Y4, Y6), it sends the pulse out. <\/p>\n<p> Y1 (Y3, Y5, Y7), it sends out the directional signal; <\/p>\n<p> ON=upward counting, OFF= downward counting. <\/p>\n<p>A\/B Mode <strong>: <\/strong>Y0 (Y2, Y4, Y6), it sends out the phase A pulse. <\/p>\n<p> Y1 (Y3, Y5, Y7), it sends out the phase B pulse. <\/p>\n<p>\u25cf The output polarity for Pulse Output can select to be Normal ON or Normal OFF. <\/p>\n<p>\uff3bThe interfaces for positioning control\uff3d<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p> M1991 <\/p>\n<\/td>\n<td>\n<p>ON <strong>:<\/strong> stop or pause FUN140, slow down and stop pulse output. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>OFF<strong> :<\/strong> stop or pause FUN140, stop pulse output immediately. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p> M1992  <\/p>\n<\/td>\n<td>\n<p>ON <strong>:<\/strong> Ps0 Ready <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>OFF<strong> :<\/strong> Ps0 is in action <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p> M1993 <\/p>\n<\/td>\n<td>\n<p>ON <strong>:<\/strong> Ps1 Ready <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>OFF<strong> :<\/strong> Ps1 is in action <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p> M1994 <\/p>\n<\/td>\n<td>\n<p>ON <strong>:<\/strong> Ps2 Ready <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>OFF<strong> :<\/strong> Ps2 is in action <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p> M1995 <\/p>\n<\/td>\n<td>\n<p>ON <strong>:<\/strong> Ps3 Ready <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>OFF<strong> :<\/strong> Ps3 is in action <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> M1996 <\/p>\n<\/td>\n<td>\n<p>ON <strong>:<\/strong> Ps0 has finished the last step <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> M1997 <\/p>\n<\/td>\n<td>\n<p>ON <strong>:<\/strong> Ps1 has finished the last step <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> M1998 <\/p>\n<\/td>\n<td>\n<p>ON <strong>:<\/strong> Ps2 has finished the last step <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> M1999 <\/p>\n<\/td>\n<td>\n<p>ON <strong>:<\/strong> Ps3 has finished the last step <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>M2000 <strong>:<\/strong> ON, multi axes acting simultaneously (At the same scan, when execution control \u201cEN\u201d= 1of FUN140 \t\t\tinstructions which control Ps0\uff5e3, their pulses output will be sent at the same time without any time lag). \t<strong> :<\/strong> OFF, as the FUN140 for Ps0\uff5e3 starts, corresponding axis pulse output will be sent immediately; since \t\tthe ladder program is executed in sequence, therefore even the FUN140 for Ps0\uff5e3 started at the same \t\tscan, there must be some time lag between them. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Ps  No. <\/p>\n<\/td>\n<td>\n<p>Current output frequency <\/p>\n<\/td>\n<td>\n<p>Current pulse position <\/p>\n<\/td>\n<td>\n<p>The remaining pulse <br \/>counts to be transmitted <\/p>\n<\/td>\n<td>\n<p>Error code<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps0 <\/p>\n<\/td>\n<td>\n<p>DR4080 <\/p>\n<\/td>\n<td>\n<p>DR4088 <\/p>\n<\/td>\n<td>\n<p>DR4072 <\/p>\n<\/td>\n<td>\n<p>R4060 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps1 <\/p>\n<\/td>\n<td>\n<p>DR4082 <\/p>\n<\/td>\n<td>\n<p>DR4090 <\/p>\n<\/td>\n<td>\n<p>DR4074 <\/p>\n<\/td>\n<td>\n<p>R4061 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps2 <\/p>\n<\/td>\n<td>\n<p>DR4084 <\/p>\n<\/td>\n<td>\n<p>DR4092 <\/p>\n<\/td>\n<td>\n<p>DR4076 <\/p>\n<\/td>\n<td>\n<p>R4062 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps3 <\/p>\n<\/td>\n<td>\n<p>DR4086 <\/p>\n<\/td>\n<td>\n<p>DR4094 <\/p>\n<\/td>\n<td>\n<p>DR4078 <\/p>\n<\/td>\n<td>\n<p>R4063 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u203b R4056 <strong>:<\/strong> When the value of low byte=5AH, it can be dynamically changed for its output frequency during the \thigh speed pulse output transmitting at any time. <\/p>\n<p> When the value of low byte is not 5AH, it can not be dynamically changed for its output frequency during the high speed pulse output transmitting. <\/p>\n<p> The default value of R4056 is 0 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-194.png\" \/><\/p>\n<p>NC Positioning Control Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 140 <\/p>\n<\/td>\n<td>\n<p>High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN 140 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>HSPSO <\/p>\n<\/td>\n<td>\n<p>(Including the extended positioning instruction) <\/p>\n<\/td>\n<td>\n<p>HSPSO <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>R4064 <strong>: <\/strong>The step number (positioning point) which has been completed of Ps0. R4065 <strong>: <\/strong>The step number (positioning point) which has been completed of Ps1. R4066 <strong>:<\/strong> The step number (positioning point) which has been completed of Ps2. R4067<strong> : <\/strong>The step number (positioning point) which has been completed of Ps3. <\/p>\n<p>z Format of positioning program: <br \/>SR: Starting register of registers block which reserved to store positioning program, explained as follows: <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>SR <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>A55AH <\/p>\n<\/td>\n<td>\n<p>The effective positioning program; its starting register must be A55AH <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>1\uff5e250 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>SR+1 <\/p>\n<\/td>\n<td>\n<p>Total steps <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>SR+2 <br \/>SR+3 <br \/>SR+4 <br \/>SR+5 <br \/>SR+6 \tThe first positioning point (step) of positioning program SR+7 \t(every step controlled by 9 registers). <\/p>\n<p>SR+8 <br \/>SR+9 <br \/>SR+10 <\/p>\n<p>The Nth step of positioning program. <\/p>\n<p>SR+N\u00d79+2 <\/p>\n<p>NC Positioning Control Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<td>\n<p>High Speed Pulse Output <br \/>(Including the extended positioning instruction) <\/p>\n<\/td>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>z Explanation for working register of instruction operation: <\/p>\n<p>WR is the starting register. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>WR+0 WR+1 WR+2 WR+3 WR+4 WR+5 WR+6 <\/p>\n<\/td>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Being executed or stopped step <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Working flag <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>WR+0 <strong>:<\/strong> If this instruction is in execution, the content of this register represents the step (1\uff5eN) being performed. if this instruction is not in execution, the content of this register represents the step where it stopped at present <br \/>When execution control \u201cEN\u201d =1, it will perform the next step, i.e. the current step plus 1 (if the current step is at the last step, it will restart to perform from the first step). <\/p>\n<p>Before starting the execution control \u201cEN\u201d =1, the user can renew the content of WR+0 to determine starting from which step to perform (when the content of WR+0 =0, and execution control \u201cEN\u201d =1, it represents that the execution starts from the first step). <\/p>\n<p>WR+1 <strong>:<\/strong> B0\uff5eB7, total steps <\/p>\n<p> B8  = ON, output paused <\/p>\n<p> B9  = ON, waiting for transfer condition <\/p>\n<p> B10 = ON, endless output (the stroke operand of DRV command is set to be 0 ) <\/p>\n<p> B12 = ON, pulse output transmitting (the status of output indicator \u201cACT\u201d) <\/p>\n<p> B13 = ON, instruction execution error (the status of output indicator \u201cERR\u201d) <\/p>\n<p> B14 = ON, finished being executed step (the status of output indicator \u201cDN\u201d) <\/p>\n<p>***  When step which has been completed, the output indication \u201cDN\u201d will turn ON and keep such status if suspending ; the user may turn OFF the status of \u201cDN\u201d by using the rising edge of output coil controlled by &quot;DN&quot; to clear the content of WR+1 register to be 0, and it can be attained. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-195.png\" \/><\/p>\n<p>NC Positioning Control Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 140 <\/p>\n<\/td>\n<td>\n<p>High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN 140 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>HSPSO <\/p>\n<\/td>\n<td>\n<p>(Including the extended positioning instruction) <\/p>\n<\/td>\n<td rowspan=\"7\">\n<p>HSPSO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Error indication <\/p>\n<\/td>\n<td>\n<p>Error code <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>0 : Error free <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>R4060\uff08Ps0\uff09<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>R4061\uff08Ps1\uff09<\/p>\n<\/td>\n<td>\n<p>1 : Parameter 0 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>R4062\uff08Ps2\uff09<\/p>\n<\/td>\n<td>\n<p>2 : Parameter 1 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>R4063\uff08Ps3\uff09<\/p>\n<\/td>\n<td>\n<p>3 : Parameter 2 error <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>4 : Parameter 3 error <br \/>5 : Parameter 4 error <\/p>\n<p>6  Parameter 5 error <br \/>7 : Parameter 6 error <br \/>8 : Parameter 7 error <br \/>9 : Parameter 8 error <br \/>10 : Parameter 9 error <\/p>\n<p> The possible error codes  for FUN141 execution <\/p>\n<p>13  Parameter 12 error <br \/>15  Parameter 14 error <br \/>30 : Error of variable address for speed setting <br \/>31 : Error of setting value for speed setting <br \/>32 : Error of variable address for stroke setting <br \/>33 : Error of setting value for stroke setting <br \/>34 : Illegal positioning program <\/p>\n<p>35 : Length error of total step <br \/>36 : Over the maximum step <br \/>37 : Limited frequency error <\/p>\n<p>The possible error codes for FUN140 execution <\/p>\n<p>38 : Initiate\/stop frequency error <br \/>39 : Over range of compensation value for movement <br \/>40 : Over range of moving stroke <br \/>41 : ABS positioning is not allowed within DRVC commands 42 : DRVC instruction not allow ABS addressing <br \/>50 : Illegal operation mode of DRVZ <br \/>51 : Illegal DOG input number <br \/>52 : Illegal PG0 input number <br \/>53 : Illegal CLR output number <br \/>60 : Illegal linear interpolation command <\/p>\n<p>Note <strong>:<\/strong> The content of error indication register will keep the latest error code.  Making sure that no more error to happen, you can clear the content of error indication register to be 0; as long as the content maintains at 0, it represents that there\u2019s no error happened. <\/p>\n<p>Editing Servo Program Table with WinProladder <\/p>\n<p> Click the \u201cServo Program Table\u201d Item which in project windows<strong> :<\/strong><\/p>\n<p> Project name  <\/p>\n<p> Table Edit  <\/p>\n<p> Servo Program Table  \u00c6 Click right button and select  \u201cNew Table\u201d <\/p>\n<p>NC Positioning Control Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<td>\n<p>High Speed Pulse Output <br \/>(Including the extended positioning instruction) <\/p>\n<\/td>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-196.png\" \/><\/p>\n<p>\u25cf Table Type <strong>:<\/strong> It will be fixed to \u201d Servo Program Table \u201d. <\/p>\n<p> \u25cf Table Name <strong>:<\/strong> For modify or debug, you can give a convenient name.<\/p>\n<p> \u25cf Table Starting address<strong> :<\/strong> Enter the address which Starting register of Servo Program Table. <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-197.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>NC Positioning Control Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<td>\n<p>High Speed Pulse Output <br \/>(Including the extended positioning instruction) <\/p>\n<\/td>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>z For easy programming and trouble shooting, the WinProladder provides the text editing environment to edit the motion program(servo program table) for FUN140 execution; Key in the complete FUN140 instruction first and then move the cursor to the position of it, pressing the hot key \u201dZ\u201d, then comes the text editing environment. The user can create the new motion program or display the existed program under this friendly user interface operation. <\/p>\n<p>z Extended positioning instructions are listed as follows: <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Instruction <\/p>\n<\/td>\n<td>\n<p>Operand <\/p>\n<\/td>\n<td>\n<p>Explanation <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>SPD <\/p>\n<\/td>\n<td>\n<p>XXXXXX or <br \/>Rxxxx   or <br \/>Dxxxx <\/p>\n<\/td>\n<td>\n<p>y Moving speed in frequency or velocity (FUN141 Parameter_0=0 represents velocity; Parameter_0=1 or 2 for frequency; the system default is frequency). The operand can be input directly with constant or variable (Rxxxx, Dxxxx); when the operand is variable, it needs 2 registers, e.g. D10 represents D10 (Low Word) and D11 (High Word), which is the setting of frequency or velocity. <\/p>\n<p>y When selecting to use the velocity setting, the system will automatically convert the velocity setting to corresponding output frequency. <\/p>\n<p>y Output frequency range: 1\u2266output frequency\u2266921600 Hz. <\/p>\n<p>*** When the output frequency is 0, this instruction will wait until the setting value isn\u2019t 0 to execute the positioning pulse output. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>DRV <\/p>\n<\/td>\n<td>\n<p>ADR \uff0c+ \uff0cXXXXXXXX\uff0cUt ADR \uff0c+ \uff0cXXXXXXXX\uff0cPs ADR \uff0c\u2212\uff0cXXXXXXXX\uff0cUt ADR \uff0c\u2212\uff0cXXXXXXXX\uff0cPs ADR \uff0c\uff0c XXXXXXXX\uff0cUt ADR \uff0c\uff0c\u2212XXXXXXXX\uff0cUt ADR \uff0c\uff0c XXXXXXXX\uff0cPs ADR \uff0c\uff0c\u2212XXXXXXXX\uff0cPs ADR \uff0c+ \uff0cRxxxx\uff0cUt <br \/>ADR \uff0c+ \uff0cRxxxx\uff0cPs <br \/>ADR \uff0c\u2212\uff0cRxxxx\uff0cUt <br \/>ADR \uff0c\u2212\uff0cRxxxx\uff0cPs <br \/>ADR \uff0c\uff0cRxxxx\uff0cUt <br \/>ADR \uff0c\uff0cRxxxx\uff0cPs <br \/>ADR \uff0c+ \uff0cDxxxx\uff0cUt <br \/>ADR \uff0c+ \uff0cDxxxx\uff0cPs <br \/>ADR \uff0c\u2212\uff0cDxxxx\uff0cUt <br \/>ADR \uff0c\u2212\uff0cDxxxx\uff0cPs <br \/>ADR \uff0c\uff0cDxxxx\uff0cUt <br \/>ADR \uff0c\uff0cDxxxx\uff0cPs <br \/>ABS \uff0c\uff0c XXXXXXXX\uff0cUt ABS \uff0c\uff0c\u2212XXXXXXXX\uff0cUt ABS \uff0c\uff0c XXXXXXXX\uff0cPs ABS \uff0c\uff0c\u2212XXXXXXXX\uff0cPs ABS \uff0c\uff0cRxxxx\uff0cUt <br \/>ABS \uff0c\uff0cRxxxx\uff0cPs <br \/>ABS \uff0c\uff0cDxxxx\uff0cUt <br \/>ABS \uff0c\uff0cDxxxx\uff0cPs <\/p>\n<\/td>\n<td>\n<p>y Moving stroke setting in Ps or mm,Deg,Inch <br \/>(When FUN141 Parameter_0=1, the setting stroke in Ut is Ps; Parameter_0=0 or 2, the setting stroke in Ut is mm, Deg, Inch; the system default for Ut is Ps). <\/p>\n<p>y When 4_th operand of DRV is Ut (not Ps) , according to parameter setting of 1, 2, 3 of FUN141, the system will convert the corresponding pulse count to output. <\/p>\n<p>yThere are 4 operands to construct DRV instruction as follows: <\/p>\n<p>1_st operand: coordinate selection. <\/p>\n<p>ADR or ABS: ADR, relative distance movement \tABS, absolute position movement <\/p>\n<p>2_nd operand: <br \/>revolving direction selection (Valid for ADR only). <\/p>\n<p>&#8216;+&#8217;  , forward or clockwise <br \/>&#8216;\u2212&#8217;  , backward or counterclockwise <br \/>&#8216;  &#8216;  ,direction is determined by the setting value <\/p>\n<p> (positive value: forward; negative value: backward) <\/p>\n<p>3_rd operand: moving stroke setting <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>XXXXXXXX: or <br \/>\u2212XXXXXXXX or Rxxxx <br \/>or Dxxxx <\/p>\n<\/td>\n<td>\n<p>It can directly input with constant or variable (Rxxxx, Dxxxx); it needs 2 registers when adopting the variable, e.g. R0 represents R0 (Low Word) and R1 (High Word) as the setting of moving stroke. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>*** When the setting of moving stroke is 0 and 1_st operand is \tADR, it represents to revolve endless. <\/p>\n<p>Stroke setting range: \u221299999999 \u2264 stroke setting \u2264 99999999 <\/p>\n<p>4_th operand: resolution of stroke setting <\/p>\n<p>Ut or Ps:for Ut, the resolution is one unit; <br \/> (it is determined by parameter 0, 3 of FUN141); for Ps, the enforced resolution is one pulse. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-198.png\" \/><\/p>\n<p>NC Positioning Control Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"6\">\n<p>FUN 140 HSPSO <\/p>\n<p>Instruction <\/p>\n<p>DRVC <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN 140 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>(Including the extended positioning instruction) <\/p>\n<\/td>\n<td>\n<p>HSPSO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Operand <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Explanation <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>ADR\uff0c+\uff0cXXXXXXXX\uff0cUt or   or    or         or ABS\uff0c\u2212\uff0c Rxxxx    \uff0cPs or <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>The usage of DRVC and the operand explanation is the same as DRV\u2019s instruction. <\/p>\n<p>*** DRVC is used to do successive speed changing control (8 speeds \tat the most). <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Dxxxx <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>*** Of the successive speed changing control, only the first DRVC <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>instruction can use the absolute value coordinate for positioning. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>*** The revolution direction of DRVC can only be decided by \u2018+\u2019 or \u2018\u2212\u2019. *** The revolution direction only determined by the first DRVC of \tsuccessive DRVC instructions; i.e. the successive speed \tchanging control can only be the same direction. <\/p>\n<p>For example: successive 3 speed changing control <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>001  SPD10000 <br \/>DRVC  ADR\uff0c+\uff0c20000\uff0cUt GOTO  NEXT <br \/>002  SPD    50000 <br \/>DRVC  ADR\uff0c+\uff0c60000\uff0cUt GOTO  NEXT <br \/>003  SPD    3000 <br \/>DRV   ADR\uff0c+\uff0c5000\uff0cUt WAIT  X0 <br \/>\t\tGOTO  1 <\/p>\n<\/td>\n<td>\n<p>* Pulse frequency = 10KHz. * Forward 20000 units. <\/p>\n<p>* Pulse frequency =50 KHz * Forward 60000 units. <\/p>\n<p>* Pulse frequency = 3KHz. <\/p>\n<p>* Forward 5000 units. <\/p>\n<p>* Wait until X0 ON to restart from \tthe first step to execute. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Note: The number of DRVC instructions must be the number of successive speeds deducted by 1, i.e. the successive speed changing control must be ended with the DRV instruction. <\/p>\n<p>y The above mentioned example is for successive 3 speeds changing control, which used 2 DRVC instructions and the third must use DRV instruction. <\/p>\n<p>y Diagram illustration for the above mentioned example: <\/p>\n<p>f<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>50000<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>f1<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>f2<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>f3<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>Ut<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>10000<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>3000<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>20000<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>60000<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>5000<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Note: Comparison explanation between the relative coordinate positioning (ADR) and the absolute coordinate positioning (ABS) <\/p>\n<p>To move from position 30000 to \u221210000, the coding for programming is: <\/p>\n<p>DRV ADR,\u2212,40000,Ut or DRV ABS, ,\u221210000,Ut <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>\uff0e\uff0e\uff0e<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>-10000 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>0 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>10000 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>20000 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>30000 <\/p>\n<\/td>\n<td>\n<p>\uff0e\uff0e\uff0e<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ut <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>To move from position \u221210000 to 10000, the coding for programming is: DRV ADR,+,20000,Ut or DRV ABS,,10000,Ut <\/p>\n<p>NC Positioning Control Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<td>\n<p>High Speed Pulse Output <br \/>(Including the extended positioning instruction) <\/p>\n<\/td>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Instruction <\/p>\n<\/td>\n<td>\n<p>Operand <\/p>\n<\/td>\n<td>\n<p>Explanation <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>WAIT <\/p>\n<\/td>\n<td>\n<p>Time, XXXXX or Rxxxx or Dxxxx <\/p>\n<p>or X0\uff5eX255 <br \/>or Y0\uff5eY255 <br \/>or M0\uff5eM1911 or S0\uff5eS999 <\/p>\n<\/td>\n<td>\n<p>y When pulse output is complete, performing the wait instruction for going \tto the next step. There are 5 kind of operands that explained as follows: <\/p>\n<p>Time: The waiting time (the unit is 0.01 second), it can be directly input with constant or variable (Rxxxx or Dxxxx); when it is time up, performs the step that assigned by GOTO. <\/p>\n<p>X0\uff5eX255: Waiting until the input status is ON, it performs the step that \tassigned by GOTO. <\/p>\n<p>Y0\uff5eY255:Waiting until the output status is ON, it performs the step that \tassigned by GOTO. <\/p>\n<p>M0\uff5eM1911: Waiting until the internal relay is ON, it performs the step that \tassigned by GOTO. <\/p>\n<p>S0\uff5eS999: Waiting until the step relay is ON, it performs the step that \tassigned by GOTO. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>ACT <\/p>\n<\/td>\n<td>\n<p>Time\uff0cXXXXX or Rxxxx or Dxxxx <\/p>\n<\/td>\n<td>\n<p>y After the time to output pulses described by operand of ACT, it performs immediately the step that assigned by GOTO, i.e. after the pulse output for a certain time, it performs the next step immediately.  The action time (the unit is 0.01 second) can be directly input with constant or variable (Rxxxx or Dxxxx); when the action time is up, it performs the step assigned by GOTO. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>EXT <\/p>\n<\/td>\n<td>\n<p> X0\uff5eX255 or Y0\uff5eY255 <br \/>or M0\uff5eM1911 or S0\uff5eS999 <\/p>\n<\/td>\n<td>\n<p>y External trigger instruction; when it is in pulse output (the number of pulses sending is not complete yet), if the status of external trigger is ON, it will perform the step assigned by GOTO immediately.  If the status of external trigger is still OFF when the pulse output has been complete, it is the same as WAIT instruction; waiting the trigger signal ON, then perform the step assigned by GOTO. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>GOTO <\/p>\n<\/td>\n<td>\n<p>NEXT <br \/>or 1\uff5eN <br \/>or Rxxxx <br \/>or Dxxxx <\/p>\n<\/td>\n<td>\n<p>y When matching the transfer condition of WAIT, ACT, EXT instruction, by using GOTO instruction to describe the step to be executed. <\/p>\n<p>NEXT: It represents to perform the next step. <\/p>\n<p>1\uff5eN: To perform the described number of step. <\/p>\n<p>Rxxxx: The step to be performed is stored in register Rxxxx. Dxxxx: The step to be performed is stored in register Dxxxx. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>MEND <\/p>\n<\/td>\n<td><\/td>\n<td>\n<p>The end of the positioning program. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>NC Positioning Control Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<td>\n<p>High Speed Pulse Output <br \/>(Including the extended positioning instruction) <\/p>\n<\/td>\n<td>\n<p>FUN 140 HSPSO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>z The coding for positioning programming <strong>:<\/strong><\/p>\n<p>First, it must complete the FUN140 instruction before the editing of positioning program, and assigned in <\/p>\n<p>FUN140 instruction the starting register of registers block to store positioning program.  While editing the <\/p>\n<p>positioning program, it will store the newly edited positioning program to the assigned registers block; for <\/p>\n<p>every one positioning point (called as one step) edited, it is controlled by 9 registers.  If there are N <\/p>\n<p>positioning points, it will be controlled by N \u00d7 9 + 2 registers in total. <\/p>\n<p>Note: The registers storing the positioning program can not be repeated in using! <\/p>\n<p>z Format and example for the positioning program 1: <\/p>\n<p>001 SPD \t5000 \t; Pulse frequency = 5KHz. <\/p>\n<p>DRV \tADR,+,10000,Ut \t; Moving forward 10000 units. <\/p>\n<p>WAIT \tTime,100 \t; Wait for 1 second. <\/p>\n<p>GOTO NEXT \t; Perform the next step. <\/p>\n<p>002 SPD \tR1000 \t; Pulse frequency is stored in DR1000 (R1001 and R1000). <\/p>\n<p>DRV \tADR,+,D100,Ut \t; Moving forward, the stroke is stored in DD100 (D101 and D100). <\/p>\n<p>WAIT \tTime,R500 \t; The waiting time is stored in R500. <\/p>\n<p>GOTO NEXT \t; To perform the next step. <\/p>\n<p>003 SPD \tR1002 \t; Pulse frequency is stored in DR1002 (R1003 and R1002). <\/p>\n<p>DRV \tADR,\u2212,D102,Ut \t; Moving backward, the stroke is stored in DD102 (D103 and D102). <\/p>\n<p>EXT \tX0 \t; When external trigger X0 (slow down point) ON, it performs the next <\/p>\n<p>GOTO NEXT             ; step immediately. <\/p>\n<p>004 SPD \t2000 \t; Pulse frequency = 2KHz. <\/p>\n<p>DRV \tADR,\u2212,R4072,Ps \t; Keep outputting the remain (stored in DR4072). <\/p>\n<p>WAIT \tX1 \t: Wait until X1 ON, <\/p>\n<p>GOTO 1 \t: Perform the first step. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-199.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-200.png\" \/><\/p>\n<p>Example for FUN140 Program Application<\/p>\n<p>Program example: Jog forward <\/p>\n<p>As the jog forward button has been pressed for less than 0.5 second (changeable), it sends out only one (changeable) pulse; <br \/>As the jog forward button has been pressed for more than 0.5 second (changeable), it continuously sends pulses out (the frequency is 10KHz, changeable), until the release of the jog forward button to stop the pulse transmitting; or it may be designed to send N pulses out at the most. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"3\">\n<p>Jog forward button<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>Condition<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>M1<\/p>\n<\/td>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>RST<\/p>\n<\/td>\n<td>\n<p>M1<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>M0<\/p>\n<\/td>\n<td>\n<p>\u2022 Clear finish signal. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>Jog <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>RST<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>R2000<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>\u2022 Perform from the first step every time. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>forward <\/p>\n<\/td>\n<td>\n<p>Servo<\/p>\n<\/td>\n<td>\n<p>Manual<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>button<\/p>\n<\/td>\n<td>\n<p>Ready<\/p>\n<\/td>\n<td>\n<p>operation<\/p>\n<\/td>\n<td>\n<p>for action<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>M0<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>M0<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>140.HSPSO<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>ACT<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1000<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps<\/p>\n<\/td>\n<td>\n<p>:              0<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Positioning Program: <\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>PAU<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>SR<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>:  R    5000<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>ERR<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>M1001<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>001 SPD 1000 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"5\">\n<p>WR<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>:  R    2000<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>DRV ADR\uff0c+\uff0c1\uff0cPs <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>WAIT TIME\uff0c50 <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>ABT<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>DN<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>M1002<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>GOTO NEXT <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>002 SPD 10000 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>DRV ADR\uff0c+\uff0c999999\uff0cUt <br \/>MEND <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>M0<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1996<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>SET<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1<\/p>\n<\/td>\n<td>\n<p>\u2022 When the last step been complete, <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>set finish signal.<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> Program example: Jog Backward <\/p>\n<p>As the jog backward button has been pressed for less than 0.5 second (changeable) it sends out only one (changeable) pulse; <br \/>As the jog backward button has been pressed for more than 0.5 second (changeable), it continuously sends pulses out (the frequency is 10KHz, changeable), until the release of the jog backward button to stop the pulse transmitting; or it may be designed to send N pulses out at the most. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"3\">\n<p>Jog forward button<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>Condition<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>M3<\/p>\n<\/td>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>RST<\/p>\n<\/td>\n<td>\n<p>M3<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>M2<\/p>\n<\/td>\n<td>\n<p>\u2022 Clear finish signal. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Jog <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Servo<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Manual<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>RST<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>R2007<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>\u2022Perform from the first step every time.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>forward <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>button<\/p>\n<\/td>\n<td>\n<p>Ready<\/p>\n<\/td>\n<td>\n<p>operation<\/p>\n<\/td>\n<td>\n<p>for action<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>M2<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>M2<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>140.HSPSO<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>ACT<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1003<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps<\/p>\n<\/td>\n<td>\n<p>:              0<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Positioning Program: <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>PAU<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>SR: :  R    5020<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>ERR<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>M1004<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"5\">\n<p>WR<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>:  R    2007<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>001 SPD 1000 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>DRV ADR\uff0c\u2212\uff0c1\uff0cPs <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>ABT<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>DN<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>M1005<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>WAIT TIME\uff0c50 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>GOTO NEXT <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>002 SPD 10000 <br \/>DRV ADR\uff0c\u2212\uff0c999999\uff0cUt <br \/>MEND<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>M2<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1996<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>SET<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M3<\/p>\n<\/td>\n<td>\n<p>\u2022 When the last step been complete, <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>set finish signal.<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-201.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-202.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-203.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-204.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-205.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-206.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-207.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-208.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-209.png\" \/><\/p>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 141 <\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"2\">\n<p>Instruction of Parameter Setting for Positioning Program <\/p>\n<\/td>\n<td>\n<p>FUN 141 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>MPARA <\/p>\n<\/td>\n<td>\n<p>MPARA <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td><\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-210.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-211.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-212.png\" \/><\/p>\n<\/td>\n<td>\n<p>Ps: The set number of Pulse Output (0\uff5e3). <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>SR: Starting register for parameter table, it has totally 18 <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"9\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-213.png\" \/><\/p>\n<\/td>\n<td rowspan=\"9\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-214.png\" \/><\/p>\n<\/td>\n<td rowspan=\"9\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-215.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-216.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-217.png\" \/><\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>HR<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>DR<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>parameters which controlled by 24 registers.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Range<\/p>\n<\/td>\n<td>\n<p>ROR<\/p>\n<\/td>\n<td>\n<p>K <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>R0 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>D0 <\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"2\">\n<p>R5000<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Ope- <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u2223<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>rand <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>R3839<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>D3999<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>R8071<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Ps <\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"2\">\n<p>0\uff5e3<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>\u25cb<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u25cb<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>SR <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u25cb<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> Instruction explanation <\/p>\n<p>1.This instruction is not necessary if the system default for parameter value is matching what users need. \tHowever, if it needs to open the parameter value to do dynamic modification, this instruction is required. <\/p>\n<p>2.This instruction incorporates with FUN140 for positioning control purpose, each axis can have one FUN140 instruction only. <\/p>\n<p>3. Whether the execution control input \u201cEN\u201d = 0 or 1, anyway, this instruction will be performed. <\/p>\n<p>4. When there is error in parameter value, the output indication \u201cERR\u201d will be ON, and the error code is appeared \tin the error code register. <\/p>\n<p>Explanation for the parameter table: <br \/>\tSR =Starting register of parameter table, suppose it is R2000. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>R2000 <\/p>\n<\/td>\n<td>\n<p>0\uff5e2 <\/p>\n<\/td>\n<td>\n<p>Parameter 0 <\/p>\n<\/td>\n<td>\n<p>System default =1 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> R2001 <\/p>\n<\/td>\n<td>\n<p>1\uff5e65535 Ps\/Rev <\/p>\n<\/td>\n<td>\n<p>Parameter 1 <\/p>\n<\/td>\n<td>\n<p>System default =2000 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>1\uff5e999999\u00b5M\/Rev <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>DR2002 <\/p>\n<\/td>\n<td>\n<p>1\uff5e999999      mDeg\/Rev <\/p>\n<\/td>\n<td>\n<p>Parameter 2 <\/p>\n<\/td>\n<td>\n<p>System default =2000 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>1\uff5e999999\u00d70.1 mInch\/Rev <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> R2004 <\/p>\n<\/td>\n<td>\n<p>0\uff5e3 <\/p>\n<\/td>\n<td>\n<p>Parameter 3 <\/p>\n<\/td>\n<td>\n<p>System default =2 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>DR2005 <\/p>\n<\/td>\n<td>\n<p>1\uff5e921600 Ps\/Sec <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Parameter 4 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>System default =460000 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>1\uff5e153000 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>DR2007 <\/p>\n<\/td>\n<td>\n<p>0\uff5e921600 Ps\/Sec <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Parameter 5 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>System default =141 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>1\uff5e153000 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> R2009 <\/p>\n<\/td>\n<td>\n<p>1\uff5e65535 Ps\/Sec <\/p>\n<\/td>\n<td>\n<p>Parameter 6 <\/p>\n<\/td>\n<td>\n<p>System default =1000 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>R2010 <\/p>\n<\/td>\n<td>\n<p>0\uff5e32767 <\/p>\n<\/td>\n<td>\n<p>Parameter 7 <\/p>\n<\/td>\n<td>\n<p>System default =0 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> R2011 <\/p>\n<\/td>\n<td>\n<p>0\uff5e30000 <\/p>\n<\/td>\n<td>\n<p>Parameter 8 <\/p>\n<\/td>\n<td>\n<p>System default =5000 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> R2012 <\/p>\n<\/td>\n<td>\n<p>0\uff5e1 <\/p>\n<\/td>\n<td>\n<p>Parameter 9 <\/p>\n<\/td>\n<td>\n<p>System default =0100H <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> R2013 <\/p>\n<\/td>\n<td>\n<p>-32768\uff5e32767 <\/p>\n<\/td>\n<td>\n<p>Parameter 10 <\/p>\n<\/td>\n<td>\n<p>System default =0 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> R2014 <\/p>\n<\/td>\n<td>\n<p>-32768\uff5e32767 <\/p>\n<\/td>\n<td>\n<p>Parameter 11 <\/p>\n<\/td>\n<td>\n<p>System default =0 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> R2015 <\/p>\n<\/td>\n<td>\n<p>0\uff5e30000 <\/p>\n<\/td>\n<td>\n<p>Parameter 12 <\/p>\n<\/td>\n<td>\n<p>System default =0 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> R2016 <\/p>\n<\/td>\n<td>\n<p>0\uff5e30000 <\/p>\n<\/td>\n<td>\n<p>Parameter 13 <\/p>\n<\/td>\n<td>\n<p>System default =500 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>DR2017 <\/p>\n<\/td>\n<td>\n<p>0\uff5e1999999 <\/p>\n<\/td>\n<td>\n<p>Parameter 14 <\/p>\n<\/td>\n<td>\n<p>System default =0 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>DR2019 <\/p>\n<\/td>\n<td>\n<p>00H~FFH <\/p>\n<\/td>\n<td>\n<p>Parameter 15 <\/p>\n<\/td>\n<td>\n<p>System default =FFFFFFFFH <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>DR2021 <\/p>\n<\/td>\n<td>\n<p>-999999\uff5e999999 <\/p>\n<\/td>\n<td>\n<p>Parameter 16 <\/p>\n<\/td>\n<td>\n<p>System default =0 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> R2023 <\/p>\n<\/td>\n<td>\n<p>0\uff5e255 <\/p>\n<\/td>\n<td>\n<p>Parameter 17 <\/p>\n<\/td>\n<td>\n<p>System default =1 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 141 MPARA <\/p>\n<\/td>\n<td>\n<p>Instruction of Parameter Setting for Positioning Program <\/p>\n<\/td>\n<td>\n<p>FUN 141 MPARA <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> Editing Servo Parameter Table with WinProladder <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> Click the \u201cServo Parameter Table\u201d Item which in project windows<strong> :<\/strong><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"3\">\n<p> Project name <\/p>\n<\/td>\n<td colspan=\"4\" rowspan=\"2\"><\/td>\n<\/tr>\n<tr>\n<td rowspan=\"5\"><\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<tr>\n<td><\/td>\n<td><\/td>\n<td>\n<p>Tabl<\/p>\n<\/td>\n<td>\n<p> Edit <\/p>\n<\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<tr>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<tr>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<tr>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> Servo Parameter Table  \u00c6 Click right button and select  \u201cNew Table\u201d <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-218.png\" \/><\/p>\n<p>\u25cf Table Type <strong>:<\/strong> It will be fixed to \u201d Servo Parameter Table \u201d. <\/p>\n<p> \u25cf Table Name <strong>:<\/strong> For modify or debug, you can give a convenient name.<\/p>\n<p> \u25cf Table Starting address<strong> :<\/strong> Enter the address which Starting register of Servo Parameter Table. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 141 MPARA <\/p>\n<\/td>\n<td>\n<p>Instruction of Parameter Setting for Positioning Program <\/p>\n<\/td>\n<td>\n<p>FUN 141 MPARA <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-219.png\" \/><\/p>\n<p>Explanation for the parameter: <\/p>\n<p>z Parameter 0: The setting of unit, its default is 1. <\/p>\n<p>y When the setting value is 0, the moving stroke and speed setting in the positioning program will all be assigned with the unit of mm, Deg, Inch, so called machine unit. <\/p>\n<p>y When the setting value is 1, the moving stroke and speed setting in the positioning program will all be assigned with the unit of Pulse, so called motor unit. <\/p>\n<p>y When the setting value is 2, the moving stroke setting in the positioning program will all be assigned with the unit of mm, Deg, Inch, and the speed setting will all be assigned with the unit of Pulse\/Sec, which is called as compound unit. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Parameter 0, unit setting <\/p>\n<\/td>\n<td>\n<p>\u201c0\u201d machine unit <\/p>\n<\/td>\n<td>\n<p>\u201c1\u201d motor unit <\/p>\n<\/td>\n<td>\n<p>\u201c2\u201d compound unit <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Parameter 1, 2 <\/p>\n<\/td>\n<td>\n<p>Must be set <\/p>\n<\/td>\n<td>\n<p>No need to set <\/p>\n<\/td>\n<td>\n<p>Must be set <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Parameter 3, 7, 10, 11 <\/p>\n<\/td>\n<td>\n<p>mm\uff0cDeg\uff0cInch <\/p>\n<\/td>\n<td>\n<p>Ps <\/p>\n<\/td>\n<td>\n<p>mm\uff0cDeg\uff0cInch <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Parameter 4,5,6,15,16 <\/p>\n<\/td>\n<td>\n<p>Cm\/Min\uff0cDeg\/Min\uff0cInch\/Min <\/p>\n<\/td>\n<td>\n<p>Ps\/Sec <\/p>\n<\/td>\n<td>\n<p>Ps\/Sec <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>z Parameter 1: Pulse count\/1-revolution, its default is 2000, i.e. 2000 Ps\/Rev. <\/p>\n<p>y The pulse counts needed to turn the motor for one revolution <br \/>\tA= 1\uff5e65535 (for value greater than 32767, it is set with unsigned decimal) Ps\/Rev y When Parameter 14 = 0, Parameter 1 is the setting for Pulse \/Rev <br \/>y When Parameter 14 \u2260 0, Parameter 14 is the setting for Pulse\/Rev <\/p>\n<p>z Parameter 2: Movement\/1 revolution, its default is 2000, i.e. 2000 Ps\/Rev. <\/p>\n<p>y The movement while motor turning for one revolution. <\/p>\n<p>B=1\uff5e999999 \u00b5M\/Rev <br \/>1\uff5e999999 mDeg\/Rev <br \/>1\uff5e999999\u00d70.1 mInch\/Rev <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-220.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-221.png\" \/><\/p>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 141 MPARA <\/p>\n<\/td>\n<td>\n<p>Instruction of Parameter Setting for Positioning Program <\/p>\n<\/td>\n<td>\n<p>FUN 141 MPARA <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>z Parameter 3: The resolution of moving stroke setting, its default is 2. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> Parameter 0 <\/p>\n<\/td>\n<td colspan=\"4\">\n<p>Set value=0, machine unit; Set value=2, compound unit; <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Set value=1 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Parameter 3 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>mm <\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"2\">\n<p>Deg <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Inch <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>motor unit (Ps) <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Set value =0 <\/p>\n<\/td>\n<td>\n<p>\u00d71 <\/p>\n<\/td>\n<td>\n<p>\u00d71 <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u00d70.1 <\/p>\n<\/td>\n<td>\n<p>\u00d71000 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Set value =1 <\/p>\n<\/td>\n<td>\n<p>\u00d70.1 <\/p>\n<\/td>\n<td>\n<p>\u00d70.1 <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u00d70.01 <\/p>\n<\/td>\n<td>\n<p>\u00d7100 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Set value =2 <\/p>\n<\/td>\n<td>\n<p>\u00d70.01 <\/p>\n<\/td>\n<td>\n<p>\u00d70.01 <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u00d70.001 <\/p>\n<\/td>\n<td>\n<p>\u00d710 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Set value =3 <\/p>\n<\/td>\n<td>\n<p>\u00d70.001 <\/p>\n<\/td>\n<td>\n<p>\u00d70.001 <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u00d70.0001 <\/p>\n<\/td>\n<td>\n<p>\u00d71 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>z Parameter 4: The limited speed setting, its default is 460000, i.e. 460000 Ps\/Sec. <\/p>\n<p>y Motor and compound unit: 1\uff5e921600 Ps\/Sec. <\/p>\n<p>y Machine unit: 1\uff5e153000 (cm\/Min, \u00d710 Deg\/Min, Inch\/Min). <br \/>However, the limited frequency can\u2019t be greater than921600 Ps\/Sec. <\/p>\n<p>f_max =\uff08V_max \u00d71000\u00d7A\uff09\/\uff086\u00d7B\uff09\u2264 921600 Ps\/Sec <br \/>f_min \u2265 1 Ps\/Sec <\/p>\n<p>Note: A = Parameter 1, B =Parameter 2. <\/p>\n<p>z Parameter 5: Initiate\/Stop speed, the default = 141. <\/p>\n<p>y Motor and compound unit: 1\uff5e921600 Ps\/Sec. <\/p>\n<p>y Machine unit: 1\uff5e15300 (cm\/Min, \u00d710 Deg\/Min, Inch\/Min). <\/p>\n<p> However, the limited frequency can\u2019t be greater than 921600 Ps\/Sec. <\/p>\n<p>z Parameter 6: Creep speed for machine zero return; the default is 1000. <\/p>\n<p>Motor and compound unit: 1\uff5e65535 Ps\/Sec <br \/>Machine unit: 1\uff5e15300 (cm\/Min, \u00d710 Deg\/Min, Inch\/Min). <\/p>\n<p>z Parameter 7: Backlash compensation, the default =0. <\/p>\n<p>y Setting range: 0\uff5e32767 Ps. <\/p>\n<p>y While backward traveling, the traveling distance will be added with this value automatically. <\/p>\n<p>z Parameter 8: Acceleration\/Deceleration time setting, the default = 5000, and the unit is mS. <\/p>\n<p>y Setting range: 0\uff5e30000 mS. <\/p>\n<p>y The setting value represents the time required to accelerate from idle state up to limited speed \tstate or decelerate from the limited speed state down to the idle state. <\/p>\n<p>y The acceleration\/deceleration is constant slope depending on Parameter 4 \/ Parameter 8 y When Parameter 12 = 0, Parameter 8 is the deceleration time <br \/>y There will have the auto deceleration function for short stroke movement. <\/p>\n<p>z Parameter 9: Rotation and zero return direction; the default is 0100H (Not used in linear interpolation mode) <\/p>\n<p>b15       b8 b7         b0<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>SR+12 <\/p>\n<\/td>\n<td>\n<p>Para 9-1 <\/p>\n<\/td>\n<td>\n<p>Para 9-0 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 141 MPARA <\/p>\n<\/td>\n<td>\n<p>Instruction of Parameter Setting for Positioning Program <\/p>\n<\/td>\n<td>\n<p>FUN 141 MPARA <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>y Parameter 9-0: Rotation direction setting; the default is 0 <br \/>Setting value =0, the present value increases while in forward pulse output; the present value decreases while in backward pulse output. <\/p>\n<p>Setting value =1, the present value decreases while in forward pulse output; the present value increases while in backward pulse output. <\/p>\n<p>y Parameter 9-1: Zero return direction setting; the default is 1 <br \/> Setting value =0, direction in which the present value increases. <\/p>\n<p> Setting value =1, direction in which the present value decreases. <\/p>\n<p>z Parameter 10: Forward movement compensation, the default = 0. <\/p>\n<p>y Setting range: \u221232768\uff5e32767 Ps. <\/p>\n<p>y When it is in forward pulse output, it will automatically add with this value as the moving \tdistance. <\/p>\n<p>z Parameter 11: Backward movement compensation, the default =0. <\/p>\n<p>y Setting range: \u221232768\uff5e32767 Ps. <\/p>\n<p>y When it is in backward pulse output, it will automatically add with this value as the moving \tdistance. <\/p>\n<p>z Parameter 12: Deceleration time setting, the default =0, and the unit is mS. \ty Setting range: 0\uff5e30000 mS. <\/p>\n<p>y When Parameter 12 = 0, Parameter 8 is the deceleration time y When Parameter 12 \u2260 0, Parameter 12 is the deceleration time <\/p>\n<p>z Parameter 13:  Interpolation time constant; the default is 500. <\/p>\n<p>y Setting range: 0\uff5e30000 mS. <\/p>\n<p>y Set the time required to achieve the speed specified by the program. (The initiate speed is \talways regarded as \u201c0.) <br \/>y This parameter is valid while interpolation control. <\/p>\n<p>z Parameter 14: Pulse count\/1-revolution, the default = 0. <\/p>\n<p>y The pulse counts needed to turn the motor for one revolution <br \/>y When Parameter 14 = 0, Parameter 1 is the setting for Pulse \/Rev y When Parameter 14 \u2260 0, Parameter 14 is the setting for Pulse\/Rev <\/p>\n<p>z Parameter 15: I\/O control interface for DRVZ; the default is FFFFFFFFH \tb15        b8 b7         b0 <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>SR+19 SR+20 <\/p>\n<\/td>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Para 15-1 <\/p>\n<\/td>\n<td>\n<p>Para 15-0 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Para 15-3 <\/p>\n<\/td>\n<td>\n<p>Para 15-2 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>y Parameter 15-0: Setting of DOG input (SR+19), it must be the input of the main unit \t\tb6~b0: Reference number of DOG input (0~15, it means X0~X15) \t\t b7=0: Contact A or Normal Open <br \/>\t\t\t =1: Contact B or Normal Close <br \/>\tb7~b0=FFH, without DOG input <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-222.png\" \/><\/p>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 141 MPARA <\/p>\n<\/td>\n<td>\n<p>Instruction of Parameter Setting for Positioning Program <\/p>\n<\/td>\n<td>\n<p>FUN 141 MPARA <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>zParameter 15-1: Setting of stroke limit input (SR+19) <\/p>\n<p>\t b14~b8: Reference number of limit input (0~125, it means X0~X125) \t b15 = 0 : Contact A or Normal Open <br \/>\t\t = 1 ; Contact B or Normal Close <br \/> b15~b8 = FFH, without limit input <\/p>\n<p>zParameter 15-2: Setting of PG0 signal input (SR+20), it must be the input of the main unit <\/p>\n<p>\t b6~b0: Reference number of PG0 input (0~15, it means X0~X15) \t b7= 0 : Start counting at front end of sensing DOG input <br \/>\t b7= 1 ; Start counting at rear end of sensing DOG input <br \/>b7~b0 = FFH, without PG0 input <\/p>\n<p>zParameter 15-3: Setting of CLR signal output (SR+20), it must be the output of the main unit <\/p>\n<p> b15~b8: Reference number of CLR output (0~23, it means Y0~Y23)  b15~b8 =FFH, without CLR output <\/p>\n<p>z Parameter 16: Machine zero point address; the default is 0. Setting range: -999999 ~ 999999 Ps <\/p>\n<p>z Parameter 17: Number of zero point signals (Sensing of PG0 input); the default is 1. Setting range : 0~255 <\/p>\n<p>count <\/p>\n<p>Speed<\/p>\n<p>Parameter 4 : Max. speed<\/p>\n<p>Work speed<\/p>\n<p>Parameter 5<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"5\">\n<p>Initiate\/Stop speed<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Parameter 8<\/p>\n<\/td>\n<td>\n<p>Parameter 8<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>Time<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>or<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Acceleration\/Deceleration <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Parameter 12<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>time setting<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>. For reference with FUN140 instruction<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-223.png\" \/><\/p>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 141 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Instruction of Parameter Setting for Positioning Program <\/p>\n<\/td>\n<td>\n<p>FUN 141 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>MPARA <\/p>\n<\/td>\n<td>\n<p>MPARA <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Speed<\/p>\n<p>Work Speed<\/p>\n<p>Parameter 5<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Initiate\/Stop speed<\/p>\n<p>Parameter 13<\/p>\n<p>Interpolation time constant<\/p>\n<\/td>\n<td>\n<p>Time<\/p>\n<p>Parameter 13<\/p>\n<p>Interpolation time constant<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>. For reference with FUN147 instruction<\/p>\n<p>\u203b The parameter 13 of the axis with longest movement is used for acceleration and deceleration control for \tlinear interpolation if each axis owns its own motion parameter table <\/p>\n<p>\u203b Using the same motion parameter table (through FUN141 and give the same starting address of SR operand for each axis) for the simultaneous linear interpolation axes, it is the best way for multi-axis linear interpolation motion control<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-224.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-225.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-226.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-227.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-228.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-229.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-230.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-231.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-232.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-233.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-234.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-235.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-236.png\" \/><\/p>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 142 P<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-237.png\" \/><\/p>\n<p>PSOFF <\/p>\n<\/td>\n<td>\n<p>Enforcing to Stop Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN 142 P<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-238.png\" \/><\/p>\n<p>PSOFF <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-239.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-240.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-241.png\" \/><\/p>\n<\/td>\n<td>\n<p>N: 0\uff5e3, enforces the assigned set number of Pulse Output <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>to stop its output. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-242.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-243.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-244.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p> Instruction Explanation <br \/>1. When stop control \u201cEN\u201d =1, or changes from 0\u21921( Pinstruction), this instruction will enforce the assigned set <\/p>\n<p>number of Pulse Output to stop its output. <\/p>\n<p>2. When applying in the process of return home , as the home has returned, it can immediately stop the pulse <\/p>\n<p>output by using this instruction, so as to make it stop at the same position every time when performing <\/p>\n<p>machine homing. <\/p>\n<p> Program example <\/p>\n<p>; When M0 changes from 0\u21921, it enforces the <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-245.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-246.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-247.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-248.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-249.png\" \/><\/p>\n<\/td>\n<td>\n<p>Ps0 to stop the pulse output.<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-250.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-251.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-252.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-253.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-254.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-255.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-256.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-257.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-258.png\" \/><\/p>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN 143 P<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>EN<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Converting the Current Pulse Value to the Displaying Value <\/p>\n<\/td>\n<td>\n<p>FUN 143 P<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>PSCNV <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>(mm, Deg, Inch, PS) <\/p>\n<\/td>\n<td>\n<p>PSCNV <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"4\">\n<p>Execution control<\/p>\n<\/td>\n<td>\n<p>Ladder symbol <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Ps: 0\uff5e3; converting the assigned pulse position to mm (Deg, <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>143P.PSCNV<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Inch, PS) which has the same unit as the set point, so <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps  :<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>as to make the current position displayed. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>D    :<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>D: Registers that store the current position after conversion. It uses 2 registers, e.g. D10 represents D10 (Low <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Word) and D11 (High Word) two registers.<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>Range<\/p>\n<\/td>\n<td>\n<p>HR<\/p>\n<\/td>\n<td>\n<p>DR<\/p>\n<\/td>\n<td>\n<p>ROR<\/p>\n<\/td>\n<td>\n<p>K <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>R0 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>D0 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>R5000<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>2 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Ope- <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>rand <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>R3839<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>D3999<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>R8071<\/p>\n<\/td>\n<td>\n<p>256<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Ps <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>0\uff5e3<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>\u25cb<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u25cb<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u25cb*<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>D <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> Instruction Explanation <\/p>\n<p>1. When execution control \u201cEN\u201d =1 or changes from 0\u21921( P instruction), this instruction will convert the assigned current pulse position (PS) to be the mm (or Deg, Inch, or PS) that has the same unit as the set value, so as to make current position displaying. <\/p>\n<p>2. After the FUN140 and FUN 147 instructions have been performed, it will then be able to get the correct \tconversion value by executing this instruction. <\/p>\n<p> Program Example <\/p>\n<p>; When M0=1, it converts the current pulse position of <br \/>Ps0 (DR4088) to the mm (or Deg or Inch or PS) that <br \/>has the same unit as the set value, and store it into the <br \/>DD10 to make the current position displaying.<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-259.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-260.png\" \/><\/p>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<td>\n<p>Multi-Axis High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-261.png\" \/><\/p>\n<\/td>\n<td colspan=\"3\">\n<p>Gp \uff1aGroup number (0~1) <br \/>SR \uff1aStarting register for positioning program (example \texplanation) <br \/>WR\uff1aStarting register for instruction operation <br \/>\t(example explanation). It controls 9 registers, \twhich the other program cannot repeat in using. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Range<\/p>\n<\/td>\n<td>\n<p>HR<\/p>\n<\/td>\n<td>\n<p>DR<\/p>\n<\/td>\n<td>\n<p>ROR<\/p>\n<\/td>\n<td>\n<p>K <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>R0 <\/p>\n<\/td>\n<td>\n<p>D0 <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>R5000<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ope- <\/p>\n<\/td>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u2223<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>rand <\/p>\n<\/td>\n<td>\n<p>R3839<\/p>\n<\/td>\n<td>\n<p>D3999<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>R8071<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Gp <\/p>\n<\/td>\n<td colspan=\"3\">\n<p>0~1<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>SR <\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u25cb<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>WR <\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>\u25cb*<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>Instruction Explanation <\/p>\n<p>1. The FUN147 (MHSPO) instruction is used to support the linear interpolation for multi-axis motion control, it consists of the motion program written and edited with tex programming.  We named every position point as a step (which includes output frequency, traveling distance, and transfer conditions). Every step of positioning point owns 15 registers for coding. <\/p>\n<p>2. The FUN147 (MHSPO) instruction can support up to 4 axes for simultaneous linear interpolation; or 2 sets of \t2-axis linear interpolation (i.e. Gp0 = Axes Ps0 &amp; Ps1 <strong>; <\/strong>Gp1 = Axes Ps2 &amp; Ps3) <\/p>\n<p>3. The best benefit to store the positioning program into the registers is that in the case of association with MMI (Man Machine Interface) to operate settings, it may save and reload the positioning program via MMI when replacing the molds. <\/p>\n<p>4. When execution control \u201cEN\u201d=1, if the other FUN147\/FUN140 instructions to control Ps0\uff5e3 are not active (corresponding status of Ps0=M1992, Ps1=M1993, Ps2=M1994, and Ps3=M1995 will be ON), it will start to execute from the next step of positioning point (when goes to the last step, it will be restarted from the first step to perform); if Ps0\uff5e3 is controlled by other FUN147\/FUN140 instruction (corresponding status of Ps0=M1992, Ps1=M1993, Ps2=M1994, and Ps3=M1995 would be OFF), this instruction will acquire the pulse output right of positioning control once the controlling FUN147\/FUN140 has released the control right. <\/p>\n<p>5. When execution control input \u201cEN\u201d =0, it stops the pulse output immediately. <\/p>\n<p>6. When output pause \u201cPAU\u201d =1 and execution control \u201cEN\u201d was 1 beforehand, it will pause the pulse output. When output pause \u201cPAU\u201d =0 and execution control is still 1, it will continue the unfinished pulse output. <\/p>\n<p>7. When output abort \u201cABT\u201d=1, it stops pulse output immediately. (When the execution control input \u201cEN\u201d becomes 1 \tnext time, it will restart from the first step of positioning point to execute.) <\/p>\n<p>8. While the pulse is in output transmitting, the output indication \u201cACT\u201d is ON. <\/p>\n<p>9. When there is execution error, the output indication \u201cERR\u201d will be ON.  (The error code is stored in the error code \tregister.)<\/p>\n<p>10.When each step of positioning point is complete, the output indication \u201cDN\u201d will be ON.<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<td>\n<p>Multi-Axis High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>*** The working mode of Pulse Output must be set (without setting, Y0\uff5eY7 will be treated as general output) to be one of U\/D, or A\/B mode, thus the Pulse Output may have a regular output. <br \/>U\/D mode <strong>: <\/strong>Y0 (Y2, Y4, Y6), it sends out upward counting pulse. <\/p>\n<p>Y1 (Y3, Y5, Y7), it sends out downward counting pulse. <\/p>\n<p>A\/B mode <strong>: <\/strong>Y0 (Y2, Y4, Y6), it sends out the phase A pulse. <\/p>\n<p>Y1 (Y3, Y5, Y7), it sends out the phase B pulse. <\/p>\n<p>\u25cf The output polarity for Pulse Output can select to be Normal ON or Normal OFF. <\/p>\n<p>\u3010The interfaces for positioning control\u3011<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>M1991 <\/p>\n<\/td>\n<td>\n<p>ON <strong>: <\/strong>Stop or pause FUN147, slow down then stop pulse output OFF <strong>: <\/strong>Stop or pause FUN147, stop pulse output immediately <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>M1992 <\/p>\n<\/td>\n<td>\n<p>ON <strong>: <\/strong>Ps0 is ready <br \/>OFF <strong>: <\/strong>Ps0 is in action <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>M1993 <\/p>\n<\/td>\n<td>\n<p>ON <strong>: <\/strong>Ps1 is ready <br \/>OFF <strong>: <\/strong>Ps1 is in action <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>M1994 <\/p>\n<\/td>\n<td>\n<p>ON <strong>: <\/strong>Ps2 is ready <br \/>OFF <strong>: <\/strong>Ps2 is in action <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>M1995 <\/p>\n<\/td>\n<td>\n<p>ON <strong>: <\/strong>Ps3 is ready <br \/>OFF <strong>: <\/strong>Ps3 is in action <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>M1934 <\/p>\n<\/td>\n<td>\n<p>ON <strong>: <\/strong>Gp0 has finished the last step <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>M1935 <\/p>\n<\/td>\n<td>\n<p>ON <strong>: <\/strong>Gp1 has finished the last step <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>DR4068 <\/p>\n<\/td>\n<td>\n<p>Gp0 vector speed <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>DR4070 <\/p>\n<\/td>\n<td>\n<p>Gp1 vector speed <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>D4060 <\/p>\n<\/td>\n<td>\n<p>Gp0 error code <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>D4061 <\/p>\n<\/td>\n<td>\n<p>Gp1 error code <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>D4062 <\/p>\n<\/td>\n<td>\n<p>The step number (positioning point) which has been completed of Gp0. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>D4063 <\/p>\n<\/td>\n<td>\n<p>The step number (positioning point) which has been completed of Gp1. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Ps  No. <\/p>\n<\/td>\n<td>\n<p>Current output frequency <\/p>\n<\/td>\n<td>\n<p>Current pulse position <\/p>\n<\/td>\n<td>\n<p>The remaining pulse <br \/>counts to be transmitted <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps0 <\/p>\n<\/td>\n<td>\n<p>DR4080 <\/p>\n<\/td>\n<td>\n<p>DR4088 <\/p>\n<\/td>\n<td>\n<p>DR4072 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps1 <\/p>\n<\/td>\n<td>\n<p>DR4082 <\/p>\n<\/td>\n<td>\n<p>DR4090 <\/p>\n<\/td>\n<td>\n<p>DR4074 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps2 <\/p>\n<\/td>\n<td>\n<p>DR4084 <\/p>\n<\/td>\n<td>\n<p>DR4092 <\/p>\n<\/td>\n<td>\n<p>DR4076 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps3 <\/p>\n<\/td>\n<td>\n<p>DR4086 <\/p>\n<\/td>\n<td>\n<p>DR4094 <\/p>\n<\/td>\n<td>\n<p>DR4078 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u203b FUN147 doesn\u2019t support dynamic change for its output frequency during the pulse transmitting.<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-262.png\" \/><\/p>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"2\">\n<p>FUN147 <br \/>MHSPO <\/p>\n<\/td>\n<td>\n<p>Multi-Axis High Speed Pulse Output <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>FUN147 <br \/>MHSPO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u25cf<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Format of positioning program with linear interpolation\uff1a<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>SR\uff1aStarting register of registers block which reserved to store positioning program, explained as follows\uff1a<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> SR <\/p>\n<\/td>\n<td>\n<p>A55CH <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\uff1bThe effective positioning program; its starting register must be A55CH<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> SR+1 <\/p>\n<\/td>\n<td>\n<p>Total steps <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> SR+2 <\/p>\n<p> SR+3 <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> \u25cf <\/p>\n<\/td>\n<td>\n<p> \u25cf <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>The first positioning point (step) of positioning program <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> \u25cf <\/p>\n<\/td>\n<td>\n<p> \u25cf <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> \u25cf <\/p>\n<\/td>\n<td>\n<p> \u25cf <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> \u25cf <\/p>\n<\/td>\n<td>\n<p> \u25cf <\/p>\n<\/td>\n<td>\n<p>(every step owns 15 registers for coding). <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> SR+14 <\/p>\n<p> SR+15 <\/p>\n<p> SR+16 <\/p>\n<p>The Nth step of positioning program. <\/p>\n<p>SR+N\u00d715+2 <\/p>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<td>\n<p>Multi-Axis High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>\u25cfExplanation for working register of instruction operation : <\/p>\n<p> WR is the starting of working registers.  <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>WR+0 WR+1 WR+2 WR+3 WR+4 WR+5 WR+6 WR+7 WR+8 <\/p>\n<\/td>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Being executed or stopped step <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Working flag <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Controlled by system <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>WR+0 <strong>: <\/strong>If this instruction is in execution, the content of this register represents the step (1\uff5eN) being performed. If this instruction is not in execution, the content of this register represents the step where it stopped at present <br \/>When execution control \u201cEN\u201d =1, it will perform the next step, i.e. the current step plus 1 (if the current step is at the last step, it will restart to perform from the first step). <\/p>\n<p>Before starting the execution control \u201cEN\u201d =1, the user can renew the content of WR+0 to determine starting from which step to perform (when the content of WR+0 =0, and execution control \u201cEN\u201d =1, it represents that the execution starts from the first step). <\/p>\n<p>WR+1 <strong>: <\/strong>B0\uff5eB7, total steps <br \/>B8 = ON, output paused <br \/>B9 = ON, waiting for transfer condition <br \/>B10 = ON, endless output <br \/>B12 = ON, pulse output transmitting (the status of output indicator \u201cACT\u201d) B13 = ON, instruction execution error (the status of output indicator \u201cERR\u201d) B14 = ON, finished being executed step (the status of output indicator \u201cDN\u201d) <\/p>\n<p>*** When step which has been completed, the output indication \u201cDN\u201d will turn ON and keep such status if suspending ; the user may turn OFF the status of \u201cDN\u201d by using the rising edge of output coil controlled by &quot;DN&quot; to clear the content of WR+1 register to be 0, and it can be attained.<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-263.png\" \/><\/p>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN147 <\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>0 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Multi-Axis High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN147 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>MHSPO <\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>MHSPO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Error code <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Error indication <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>R4060\uff08Ps0\uff09<\/p>\n<\/td>\n<td>\n<p>\uff1aError free <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>R4061\uff08Ps1\uff09<\/p>\n<\/td>\n<td>\n<p>1 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 0 error <\/p>\n<\/td>\n<td rowspan=\"6\">\n<p> The possible error codes<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>R4062\uff08Ps2\uff09<\/p>\n<\/td>\n<td>\n<p>2 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 1 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>R4063\uff08Ps3\uff09<\/p>\n<\/td>\n<td>\n<p>3 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 2 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>D4060\uff08Gp0\uff09<\/p>\n<\/td>\n<td>\n<p>4 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 3 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"27\">\n<p>D4061\uff08Gp1\uff09<\/p>\n<\/td>\n<td>\n<p>5 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 4 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>6 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 5 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>7 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 6 error <\/p>\n<\/td>\n<td>\n<p> For FUN141 execution <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>8 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 7 error <\/p>\n<\/td>\n<td rowspan=\"15\">\n<p>The possible error codes<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>9 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 8 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>10 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 9 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>13 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 12 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>14 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 13 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>15 <\/p>\n<\/td>\n<td>\n<p>\uff1aParameter 14 error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>30 <\/p>\n<\/td>\n<td>\n<p>\uff1aError of variable address for speed setting <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>31 <\/p>\n<\/td>\n<td>\n<p>\uff1aError of setting value for speed setting <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>32 <\/p>\n<\/td>\n<td>\n<p>\uff1aError of variable address for stroke setting <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>33 <\/p>\n<\/td>\n<td>\n<p>\uff1aError of setting value for stroke setting <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>34 <\/p>\n<\/td>\n<td>\n<p>\uff1aIllegal positioning program <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>35 <\/p>\n<\/td>\n<td>\n<p>\uff1aLength error of total step <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>36 <\/p>\n<\/td>\n<td>\n<p>\uff1aOver the maximum step <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>37 <\/p>\n<\/td>\n<td>\n<p>\uff1aLimited frequency error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>38 <\/p>\n<\/td>\n<td>\n<p>\uff1aInitiate\/stop frequency error <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>39 <\/p>\n<\/td>\n<td>\n<p>\uff1aOver range of compensation value for movement <\/p>\n<\/td>\n<td>\n<p> For FUN140 and  <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>40 <\/p>\n<\/td>\n<td>\n<p>\uff1aOver range of moving stroke <\/p>\n<\/td>\n<td rowspan=\"8\">\n<p> FUN147 execution <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>41 <\/p>\n<\/td>\n<td>\n<p>\uff1aABS positioning is not allowed within DRVC commands <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>42 <\/p>\n<\/td>\n<td>\n<p>\uff1aDRVZ can\u2019t follow DRVC <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>50 <\/p>\n<\/td>\n<td>\n<p>\uff1aIllegal operation mod of DRVZ <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>51 <\/p>\n<\/td>\n<td>\n<p>\uff1aIllegal DOG input number <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>52 <\/p>\n<\/td>\n<td>\n<p>\uff1aIllegal PG0 input number <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>53 <\/p>\n<\/td>\n<td>\n<p>\uff1aIllegal CLR output number <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>60 <\/p>\n<\/td>\n<td>\n<p>\uff1aIllegal linear interpolation command <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Note <strong>: <\/strong>The content of error indication register will keep the latest error code. Making sure that no more error to \thappen, you can clear the content of error indication register to be 0, and it still maintains the value at 0.<\/p>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<td>\n<p>Multi-Axis High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> Editing Servo Program Table with WinProladder <\/p>\n<p> Click the \u201cServo Program Table\u201d item which in project window<strong>: <\/strong><\/p>\n<p>Project Name <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"2\"><\/td>\n<\/tr>\n<tr>\n<td><\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> Table Edit  <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> Servo Program Table  \u00c6 Click right button and select \u201cNew Table\u201d <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-264.jpg\" \/><\/p>\n<p>\u25cf Table Type: Multi-Axis positioning table <\/p>\n<p>\u25cf Table Name: For modify or debug, you can give a convenient name. <\/p>\n<p>\u25cf Table Starting address: Enter the address which Starting register <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-265.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<td>\n<p>Multi-Axis High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>z \tFor easy programming and trouble shooting, the WinProladder provides the text editing environment to edit <\/p>\n<p>the motion program (servo program table) for FUN147 execution. <\/p>\n<p>z \tExtended positioning instructions for linear interpolation are listed as follows: <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Instruction <\/p>\n<\/td>\n<td>\n<p>Operand <\/p>\n<\/td>\n<td>\n<p>Explanation <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>SPD <\/p>\n<\/td>\n<td>\n<p>XXXXXX or <br \/>Rxxxx   or <br \/>Dxxxx <\/p>\n<\/td>\n<td>\n<p>y Setting of the vector speed for linear interpolation <br \/>\t1 \u2266 setting value \u2266 1840000 <br \/>y Moving speed in frequency or velocity (FUN141 Parameter_0=0 \trepresents velocity; Parameter_0=1 or 2 for frequency; the \tsystem default is frequency). The operand can be input directly \twith constant or variable (Rxxxx, Dxxxx); when the operand is \tvariable, it needs 2 registers, e.g. D10 represents D10 (Low \tWord) and D11 (High Word), which is the setting of frequency or \tvelocity. <\/p>\n<p>y When selecting to use the velocity setting, the system will <br \/>\tautomatically convert the velocity setting to corresponding output \tfrequency <br \/>y The corresponding axis frequency for output will be calculate \tfrom the setting of the vector speed <br \/>y Output frequency range: 1\u2266output frequency\u2266921600 Hz.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>LIN <\/p>\n<\/td>\n<td>\n<p>ADR\uff0cX\uff0cY\uff0cZ\uff0cW\uff0cUt <\/p>\n<p>or                   or ABS                Ps <\/p>\n<p>Where, <br \/>X\uff1aStroke setting of Ps0 Y\uff1aStroke setting of Ps1 Z\uff1aStroke setting of Ps2 W\uff1aStroke setting of Ps3 <\/p>\n<\/td>\n<td>\n<p>y Moving stroke setting in Ps or mm,Deg,Inch (When FUN141 Parameter_0=1, the setting stroke in Ut is Ps; Parameter_0=0 or 2, the setting stroke in Ut is mm, Deg, Inch; the system default for Ut is Ps). <\/p>\n<p>y When 6_th operand of LIN is Ut (not Ps) , according to the settings of parameter 1, 2, 3 of FUN141, the system will convert the corresponding pulse count to output. <\/p>\n<p>y There are 6 operands to construct LIN instruction as follows: 1_st operand: coordinate selection. <\/p>\n<p>\tADR or ABS: ADR, relative distance movement <br \/>\t\tABS, absolute position movement <br \/>2_nd\uff5e5_th operands: moving stroke setting for each axis <\/p>\n<p>It can directly input with constant or XXXXXXXX: variable (Rxxxx, Dxxxx); it needs 2 <br \/>or registers when adopting the variable, e.g. <\/p>\n<p>\u2212XXXXXXXX R0 represents R0 (Low Word) and R1 or Rxxxx (High Word) as the setting of moving or Dxxxx stroke. <\/p>\n<p>Positive setting value moves forward Negative setting value moves backward <\/p>\n<p>*** When the setting of moving stroke is 0 or in space and 1_st \toperand is ADR, it means no movement for this axis <br \/>*** When the setting of moving stroke is in space and 1_st operand \tis ABS, it means no movement for this axis <\/p>\n<p>Maximum setting for one movement must be under \u00b11999999 Ps 6_th operand: resolution of stroke setting <br \/>Ut or Ps: for Ut, the resolution is one unit <br \/>(it is determined by parameter 0, 3 of FUN141); for Ps, the <br \/>enforced resolution is one pulse. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-266.png\" \/><\/p>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"4\">\n<p>FUN147 MHSPO <\/p>\n<p>Instruction <\/p>\n<p>LINE <\/p>\n<\/td>\n<td colspan=\"3\">\n<p>Multi-Axis High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN147 <br \/>MHSPO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Operand <\/p>\n<\/td>\n<td colspan=\"3\">\n<p>Explanation <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>ADR\uff0cX\uff0cY\uff0cZ\uff0cW\uff0cUt <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>yLINE is used for linear interpolation in endless movement <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>or                  or ABS               Ps <\/p>\n<\/td>\n<td colspan=\"3\">\n<p>yThere are 6 operands to construct LINE instruction as LIN\u2019s Description <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Where, <br \/>X\uff1aStroke setting of Ps0 Y\uff1aStroke setting of Ps1 Z\uff1aStroke setting of Ps2 W\uff1aStroke setting of Ps3 <\/p>\n<p>yThe stroke setting for each axis means the output ratio between the active axes, the axis with longest movement is followed by others <\/p>\n<p>i.e. In LINE mode, if the stroke settings are 1000\u3001500\u3001300\u30010( In <\/p>\n<p>Ps), it means if Ps0 axis sends 1000Ps, then Ps1 and Ps2 will send 500Ps and 300Ps respectively. (Axis Ps3 doesn\u2019t work due to the setting value is 0). <\/p>\n<p>It will follow this ratio (1000\/500\/300\/0) for pulse output until the FUN147 instruction is stopped or exists from the LINE mode. <\/p>\n<p>Note: Comparison explanation between the relative coordinate positioning (ADR) and the absolute coordinate <\/p>\n<p>positioning (ABS)<\/p>\n<p>To move from position 30000 to -10000, the coding for programming is: <\/p>\n<p>DRV ADR,\u2212,40000,Ut or DRV ABS, ,\u221210000,Ut <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>\uff0e\uff0e\uff0e<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>-10000 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>0 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>10000 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>20000 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>30000 <\/p>\n<\/td>\n<td>\n<p>\uff0e\uff0e\uff0e<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ut <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>To move from position\u221210000 to 10000, the coding for programming is: DRV ADR,+,20000,Ut or DRV ABS,,10000,Ut <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Instruction <\/p>\n<\/td>\n<td>\n<p>Operand <\/p>\n<\/td>\n<td>\n<p>Explanation <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"5\">\n<p>WAIT <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>TIME\uff0cXXXXX <\/p>\n<\/td>\n<td>\n<p>y When pulse output is complete, performing the wait instruction to <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>go to the assigned step. There are 5 kind of operands that <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> or Rxxxx <\/p>\n<\/td>\n<td>\n<p>explained as follows: <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p> or Dxxxx <\/p>\n<\/td>\n<td>\n<p>Time: The waiting time (the unit is 0.01 second), it can be directly <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>input with constant or variable (Rxxxx or Dxxxx); when it is <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>time up, performs the step that assigned by GOTO. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>or X0\uff5eX255 <br \/>or Y0\uff5eY255 <br \/>or M0\uff5eM1911 <br \/>or S0\uff5eS999 <\/p>\n<\/td>\n<td>\n<p>X0\uff5eX255: Waiting until the input status is ON, it performs the step that assigned by GOTO. <\/p>\n<p>Y0\uff5eY255:Waiting until the output status is ON, it performs the step that assigned by GOTO. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>M0\uff5eM1911: Waiting until the internal relay is ON, it performs the step that assigned by GOTO. <\/p>\n<p>S0\uff5eS999: Waiting until the step relay is ON, it performs the step \tthat assigned by GOTO. <\/p>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<td>\n<p>Multi-Axis High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>EXT <\/p>\n<\/td>\n<td>\n<p>X0\uff5eX255 <br \/>or Y0\uff5eY255 <br \/>or M0\uff5eM1911 or S0\uff5eS999 <\/p>\n<\/td>\n<td>\n<p>yExternal trigger instruction; when it is in pulse output (the number of pulses sending is not complete yet), if the status of external trigger is ON, it will perform the step assigned by GOTO immediately. If the status of external trigger is still OFF when the pulse output has been complete, it is the same as WAIT instruction; waiting the trigger signal ON, then perform the step assigned by GOTO. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>GOTO <\/p>\n<\/td>\n<td>\n<p>NEXT <br \/>or 1\uff5eN <br \/>or Rxxxx <br \/>or Dxxxx <\/p>\n<\/td>\n<td>\n<p>y When matching the transfer condition of WAIT, ACT, EXT instruction, by \tusing GOTO instruction to describe the step to be executed. <\/p>\n<p>NEXT: It represents to perform the next step. 1\uff5eN : To perform the described number of step <\/p>\n<p>Rxxxx: The step to be performed is stored in register Rxxxx Dxxxx: The step to be performed is stored in register Dxxxx <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>MEND <\/p>\n<\/td>\n<td><\/td>\n<td>\n<p>End of the positioning program. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>z<\/p>\n<\/td>\n<td>\n<p>The editing for positioning programming with linear interpolation<strong>:<\/strong><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>First, it must complete the FUN147 instruction before the editing of positioning program, and assigned in <\/p>\n<p>FUN147 instruction the starting register of registers block to store positioning program. While editing the <\/p>\n<p>positioning program, it will store the newly edited positioning program to the assigned registers block; for <\/p>\n<p>every one positioning point (called as one step) edited, it owns 15 registers for coding. If there are N <\/p>\n<p>positioning points, it will be used by N \u00d7 15 + 2 registers in total. <\/p>\n<p>Note: The registers storing the positioning program can not be repeated in using!<\/p>\n<p>z Format and example for the positioning program with linear interpolation: <\/p>\n<p>001 SPD 5000 \t\uff1bVector speed is 5KHz <\/p>\n<p>LIN ADR,500,400,300,200,Ut       \uff1bMoving forward 500(Ps0)\/400(Ps1)\/300(Ps2)\/200(Ps3) units <\/p>\n<p>WAIT \tTIME,100 \t\uff1bWait for 1second <\/p>\n<p>GOTO \tNEXT \t\uff1bPerform the next step <\/p>\n<p>002 SPD R1000 \t\uff1bVector speed is stored in DR1000\uff08R1001 and R1000\uff09<\/p>\n<p>LIN \tADR,D100,D200, , \t,Ut      \uff1bMoving stroke is stored in DD100(Ps0) &amp; DD200(Ps1) <\/p>\n<p>WAIT TIME,R500 \t\uff1bThe waiting time is stored in R500 <\/p>\n<p>GOTO \tNEXT \t\uff1bTo perform the next step <\/p>\n<p>003 SPD R1002 \t\uff1bVector speed is stored in DR1002\uff08R1003 and R1002\uff09<\/p>\n<p>LIN ADR,0,0,R300,R400,Ps        \uff1bMoving stroke is stored in DR300(Ps2) &amp; DR400(Ps3) <\/p>\n<p>WAIT X0 \t\uff1bWait until X0 ON <\/p>\n<p>GOTO \t1                            \uff1bPerform the first step <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<td>\n<p>Multi-Axis High Speed Pulse Output <\/p>\n<\/td>\n<td>\n<p>FUN147 MHSPO <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> Example and figure for description <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>The positioning program with linear interpolation instruction as below<strong>:<\/strong><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-267.jpg\" \/><\/p>\n<p>It means the moving stroke setting for axis Ps0(X axis) is 1000 Ps, for axis Ps1(Y axis) is 500 Ps; both axes Ps2 <\/p>\n<p>and Ps3 are inactive due to the setting values are 0. <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-268.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-269.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-270.png\" \/><\/p>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<td>\n<p>Manual Pulse Generator For Positioning <\/p>\n<\/td>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"3\">\n<p> 148. MPG <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> Ps : <br \/> Fo :         Mr : <\/p>\n<p>WR : <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Execution EN    <s>  <\/s> Sc :       <s>  <\/s>ACT <\/p>\n<\/td>\n<td colspan=\"4\">\n<p>Sc \uff1a Source of high speed counter; 0~7 <br \/>Ps \uff1a Axis of pulse output; 0~3 <br \/>Fo \uff1a Setting of output speed (2 registers) <br \/>Mr \uff1a Setting of multiplier (2 registers) <br \/>\tMr+0\uff1a Multiplicand (Fa) <br \/>\tMr+1\uff1a Dividend (Fb) <br \/>WR\uff1aStarting address of working registers, it needs 4 registers <\/p>\n<p>\uff0a This instruction can be supported in PLC OS firmware \tV4.60 or late <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Range<\/p>\n<\/td>\n<td>\n<p>HR<\/p>\n<\/td>\n<td>\n<p>ROR<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>DR<\/p>\n<\/td>\n<td>\n<p>K <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>R0 <\/p>\n<\/td>\n<td>\n<p>R5000<\/p>\n<\/td>\n<td colspan=\"3\">\n<p>D0 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Ope- <\/p>\n<\/td>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<td>\n<p>\u2223<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>16 bit<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>rand <\/p>\n<\/td>\n<td>\n<p>R3839<\/p>\n<\/td>\n<td>\n<p>R8071<\/p>\n<\/td>\n<td colspan=\"3\">\n<p>D3999<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Sc <\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>0~7<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Ps <\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>0~3<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Fo <\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td colspan=\"3\">\n<p>\u25cb<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Mr <\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td colspan=\"3\">\n<p>\u25cb<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>WR <\/p>\n<\/td>\n<td>\n<p>\u25cb<\/p>\n<\/td>\n<td>\n<p>\u25cb*<\/p>\n<\/td>\n<td colspan=\"3\">\n<p>\u25cb<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u25cf<\/p>\n<\/td>\n<td colspan=\"6\">\n<p>Let this instruction be executed in 50mS fixed time interrupt service routine (50MSI)\u3001or by using the 0.1mS high <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>speed timer to generate 50mS fixed time interrupt service to have accurate repeat time to sample the pulse input from manual pulse generator. If it comes the input pulses, it will calculate the number of pulses needing to output according to the setting of multiplier (Mr+0 and Mr+1), and then outputs the pulse stream in the speed of setting (Fo) during this time interval. <\/p>\n<p>The setting of output speed (Fo) must be fast enough, and the acceleration \/ deceleration rate ( Parameter 4 and parameter 8 of FUN141 instruction) must be sharp to guarantee it can complete the sending of pulse stream during the time interval if it is under high multiplier (100 or 200 times) situation. <\/p>\n<p>\u25cf\tWhen execution \u301dEN\u301e=1, this instruction will sample the pulse input from manual pulse generator by reading the \tcurrent value of assigned high speed counter every time interval; it doesn\u2019t have any output if it doesn\u2019t have any \tinput pulse; but If it senses the input pulses, it will calculate the number of pulses needing to output according to \tthe setting of multiplier (Mr+0 and Mr+1), and then outputs the pulse stream in the speed of setting (Fo) during \tthis time interval. <\/p>\n<p>Number of output pulses = (Number of input pulses \u00d7 Fa ) \/ Fb <\/p>\n<p>\u25cf\tThis instruction also under the control of hardware resource management; it wouldn\u2019t be executed if the \thardware is occupied. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"3\">\n<p>\u25cf<\/p>\n<\/td>\n<td colspan=\"4\">\n<p>The output indicator ACT=1 if it outputs the pulses; otherwise ACT=0. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>50mS<\/p>\n<\/td>\n<td colspan=\"3\">\n<p>50mS<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-271.png\" \/>\uff0eOutput pulse stream in <\/p>\n<p>the second of Fo\t<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-272.png\" \/><\/p>\n<p>\uff0eSample pulse input <\/p>\n<\/td>\n<td>\n<p> \u2026<\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-273.png\" \/>\uff0eOutput pulse stream in <\/p>\n<p>the speed of Fo\t<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-274.png\" \/><\/p>\n<p>\uff0eSample pulse input <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<td>\n<p>Manual Pulse Generator For Positioning <\/p>\n<\/td>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Example 1: <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-275.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-276.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<td>\n<p>Manual Pulse Generator For Positioning <\/p>\n<\/td>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-277.jpg\" \/><\/p>\n<p>X32 \uff1aSelect axis 0(Ps0) <br \/>X33 \uff1aSelect axis 1 (Ps1) <br \/>X34 \uff1aMultiplier = 1 <br \/>X35 \uff1aMultiplier = 10 <br \/>X36 \uff1aMultiplier = 100 <br \/>M100\uff1aEnable \/ disable MPG activity <br \/>DR2005\uff1aMaximum speed of axis 0(Parameter 4 of FUN141)\uff1b200K Hz <br \/>R2011 \uff1aAcc\/Dec time of axis 0(Parameter 8 of FUN141)\uff1b30mS <br \/>DD600\uff1aOutput speed of axis 0 for MPG; 200K Hz <br \/>DR2105\uff1a Maximum speed of axis 1 (Parameter 4 of FUN141) ; 200K Hz <br \/>R2111 \uff1a Acc\/Dec time of axis 1 (Parameter 8 of FUN141); 30mS <br \/>DD602\uff1a Output speed of axis 1 for MPG; 200K Hz <br \/>Description\uff1a Let the MPG instruction (FUN148) be executed in 50mS fixed time interrupt service routine (50MSI) to handle the MPG positioning of Ps0 and Ps1. When X32=1 and M100=1, it will handle the MPG positioning of Ps0; it will sample the pulse input from reading the current value of HSC0 every 50mS time interval; it doesn\u2019t have any output if it doesn\u2019t have any input pulse; but If it senses the input pulses, it will calculate the number of pulses needing to output according to the setting of multiplier (D700 and D701), and then outputs the pulse stream in the speed of setting (DD600) during this time interval. <\/p>\n<p>.Number of output pulses = (Number of input pulses from HSC0 \u00d7 D700) \/ D701 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<td>\n<p>Manual Pulse Generator For Positioning <\/p>\n<\/td>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> Example 2\uff1a<\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-278.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-279.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>NC Positioning Instruction <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<td>\n<p>Manual Pulse Generator For Positioning <\/p>\n<\/td>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-280.jpg\" \/><\/p>\n<p>X32 \uff1a Select axis 0 (Ps0) <br \/>X33 \uff1a Select axis 1 (Ps1) <br \/>X34 \uff1a Multiplier = 1 <br \/>X35 \uff1aMultiplier = 10 <br \/>X36 \uff1a Multiplier = 100 <br \/>M100\uff1a Enable\/disable MPG activity <br \/>DR2005\uff1a Maximum speed of axis 0 (Parameter 4 of FUN141) ; 200K Hz <br \/>R2011 \uff1a Acc\/Dec time of axis 0 (Parameter 8 of FUN141); 30mS <br \/>DD600\uff1a Output speed of axis 0 for MPG; 200K Hz <br \/>DR2105\uff1a Maximum speed of axis 1 (Parameter 4 of FUN141) ; 200K Hz <br \/>R2111 \uff1a Acc\/Dec time of axis 1 (Parameter 8 of FUN141); 30mS <br \/>DD602\uff1a Output speed of axis 1 for MPG; 200K Hz <br \/>Description\uff1a By using the 0.1mS high speed timer to generate 50mS fixed time interrupt service (HSTAII) to \t\thandle the MPG positioning of Ps0 and Ps1. When X33=1 and M100=1, it will handle the MPG \t\tpositioning of Ps1; it will sample the pulse input from reading the current value of HSC0 every \t\t50mS time interval; it doesn\u2019t have any output if it doesn\u2019t have any input pulse; but If it senses the \t\tinput pulses, it will calculate the number of pulses needing to output according to the setting of \t\tmultiplier (D700 and D701), and then outputs the pulse stream in the speed of setting (DD602) \t\tduring this time interval. <\/p>\n<p>.Number of output pulses = (Number of input pulses from HSC0 \u00d7 D700) \/ D701 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p> NC Positioning Instruction<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<td>\n<p>Manual Pulse Generator For Positioning <\/p>\n<\/td>\n<td>\n<p>FUN148 MPG <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>Manual Pulse Generator(FUN148\uff0cMPG) instruction supports most left\/right limitation for positioning control . High byte value of R4020 \u226055H, not support this function\uff1b <br \/> High byte value of R4020 = 55H, bits of low byte are used for most left\/right limitation <br \/> R4020_ b15\u2026b8=55H\uff0c <br \/> R4020_ b0=1\uff0cnot allowed forward movement of Ps0 <br \/> R4020_ b1=1\uff0cnot allowed backward movement of Ps0 <br \/> R4020_ b2=1\uff0cnot allowed forward movement of Ps1 <br \/> R4020_ b3=1\uff0cnot allowed backward movement of Ps1 <br \/> R4020_ b4=1\uff0cnot allowed forward movement of Ps2 <br \/> R4020_ b5=1\uff0cnot allowed backward movement of Ps2 <br \/> R4020_ b6=1\uff0cnot allowed forward movement of Ps3 <br \/> R4020_ b7=1\uff0cnot allowed backward movement of Ps3<\/p>\n<p>. Program example <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-281.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-282.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-283.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-284.png\" \/><\/p>\n<h3>11.7 Machine Homing <\/h3>\n<p>The machine set which undertakes relative model Encoder as shifting detector usually need the reset action for the reference of positioning coordinate; we called this action as machine homing (seeking for zero reference). <\/p>\n<p>The machine homing diagram for NC servo unit is as follows: <\/p>\n<p>Method 1: <br \/>\tReturn home speed <\/p>\n<p>Slow down speed <\/p>\n<p>Left over travel limit switch \tNear home sensing Right over travel limit switch <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-285.png\" \/><\/p>\n<p>When it encounters the near home signal, starts the Z phase counting. <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-286.png\" \/><\/p>\n<p>Z phase counting is up, the pulse output stops, then send out the CLR signal to clear the error counter of servo driver. <\/p>\n<p>e.g.: <br \/>X3: Near home sensing input is configured as interrupt input; in the case of machine homing, it starts HSC4 to begin counting in X3+ interrupt service subroutine. <\/p>\n<p>X2: Z phase counting input, it is configured as UP input of HSC4; the X2+ is prohibited to interrupt in regular time, when executing machine homing and X3 near home interrupt occurred, it starts HSC4 to begin Z phase counting. When HSC4 counting is up, it stops the pulse output, prohibit the X2+ interrupt,set home position to signal, and sends out the CLR signal to clear the error counter of servo driver.  Please consult program example. <\/p>\n<p>Method 2: According to application demand, it may slow down when encountering the near home sensor, while over the sensor a little far away, stop the pulse output, and then traveling slowly with backward direction; the very moment when it get out of near home sensor (the sensing signal changes from 1\u21920),it is treated as machine home.  This program is simpler! <\/p>\n<p>(1) <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>(3) <\/p>\n<\/td>\n<td colspan=\"2\">\n<p>(2) Slow down <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Home speed <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>speed <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>Stop<\/p>\n<\/td>\n<td>\n<p>(4) <\/p>\n<\/td>\n<td>\n<p>Slowly<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>(5) <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\" rowspan=\"2\">\n<p>backward <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Stop<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>Near home signal 1\u21920, machine zero reference <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Left over travel limit switch <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Near home sensing <\/p>\n<\/td>\n<td>\n<p>Right over travel limit switch <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-287.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-288.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>X3: Near home sensing input; it is configured as falling edge interrupt input. <\/p>\n<p>\u2022Once encountering the near home sensor, it will enable X3 falling edge interrupt, and slow down to stop \twithin the near home sensing range. <\/p>\n<p>\u2022Slowly backward traveling until the near home sensing signal changes from 1\u21920. <\/p>\n<p>\u2022When the near home sensing signal changes from 1\u21920, it performs the X3- interrupt service subroutine \timmediately. <\/p>\n<p>\u2022The X3- interrupt service subroutine: Stops the pulse output immediately, prohibits the X3- interrupt, sets home position to signal, and sends out CLR signal to clear the error counter of servo driver.  (Please consult the example program.) <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-289.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> Program Example 1: Machine homing (method 1) <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>X2: Configured as the UP input of HSC4, and connected to Z phase input. <\/p>\n<p>X3: Configured as the rising edge interrupt input, and connected to near home sensing input. <\/p>\n<p>\u3010Main Program\u3011<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"7\">\n<p>M1924<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>EN<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>146<\/p>\n<\/td>\n<td rowspan=\"7\">\n<p>ERR<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>\u2022 Prohibits X2+ interruption <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>DIS<\/p>\n<\/td>\n<td>\n<p>X2+I<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\" rowspan=\"4\">\n<p>141.MPARA<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>(HSC4 does not count) <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>\u2022 Parameter table R2900\u2192R2923. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps<\/p>\n<\/td>\n<td>\n<p>:               0<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>SR:   R   2900<\/p>\n<p>M92<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>RST<\/p>\n<\/td>\n<td>\n<p>M50<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Clears the homing completion signal.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>RST<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>M5<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u2022 Clears the instruction completion <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>signal for homing <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>RST<\/p>\n<\/td>\n<td>\n<p>M1007<\/p>\n<\/td>\n<td>\n<p>\u2022 Clears the error signal. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u2022 Clears the step pointer, it starts from <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>RST<\/p>\n<\/td>\n<td>\n<p>R   2014<\/p>\n<\/td>\n<td>\n<p>the first step to execute. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td>\n<p>D<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>R   4112<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Clears the current value of HSC4. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>RST<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u2022 Clears the High Word of preset value <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"6\">\n<p>M92<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>SERVO<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>Manual<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>M5<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>M50M1007<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>RST<\/p>\n<\/td>\n<td>\n<p>R   4115<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>M4<\/p>\n<\/td>\n<td>\n<p>for HSC4. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\" rowspan=\"2\">\n<p>08.MOV<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Fill the preset value of HSC4 with <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"4\">\n<p>EN<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>S<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>:   R   2923<\/p>\n<\/td>\n<td>\n<p>the content of Parameter 17 of <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>D<\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"2\">\n<p>:   R   4114<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>FUN141. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>READY<\/p>\n<\/td>\n<td>\n<p>operation<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>M4<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"11\">\n<p>M4<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>Positioning program: <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>140.HSPSO<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>ACT<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1006<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Configure R5000\uff5eR5199 as the <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps<\/p>\n<\/td>\n<td>\n<p>:              0<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"6\">\n<p>PAU<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>SR<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>:  R    5040<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>ERR<\/p>\n<\/td>\n<td rowspan=\"9\">\n<p>M1007<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>read only register (ROR) before <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>001 SPD R2919 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>programming, after then, when <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>DRV ADR,\u2212,999999,Ut <\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>WR<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>:  R    2014<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>storing program, the Ladder <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>EXT X3 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>GOTO NEXT <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>ABT<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>DN<\/p>\n<\/td>\n<td>\n<p>program will automatically contains <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>002 SPD R2921 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>the positioning program. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>DRV ADR,\u2212,9999,Ut <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>MEND <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>M4<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>M1996<\/p>\n<\/td>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>SET<\/p>\n<\/td>\n<td>\n<p>M5<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>TUP<\/p>\n<\/td>\n<td>\n<p>\u2022 Homing instruction completed <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>Y8<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td>\n<p>.01S<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>50<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Signal for homing completion <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>T0<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u2022 Fill the current PS registers with 0, <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"4\">\n<p>T0<\/p>\n<\/td>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>RST<\/p>\n<\/td>\n<td>\n<p>Y8<\/p>\n<\/td>\n<td>\n<p>while homing completed. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>D<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>R   4088<\/p>\n<\/td>\n<td>\n<p>\u2022 Signal to clear error counter of servo <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>driver &#8212; Y8 is ON for 0.5 second.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>RST<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-290.png\" \/><\/p>\n<p>\u3010Sub Program\u3011<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"3\">\n<p>M4<\/p>\n<\/td>\n<td>\n<p>65<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>X3+I<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>145<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>X2+I<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 X3 rising edge interrupt service subroutine.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>LBL<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>\u2022 Enables HSC4 counting if homing. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>69<\/p>\n<p>RTI<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"10\">\n<p>M4<\/p>\n<\/td>\n<td>\n<p>65<\/p>\n<\/td>\n<td rowspan=\"10\">\n<p>HSC4I<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>142<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>0<\/p>\n<\/td>\n<td rowspan=\"9\">\n<p>Y8<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Interrupt service subroutine of HSC4 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"9\">\n<p>LBL<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>(Z phase counting is up) <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>\u2022 Stops pulse output immediately. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>PSOFF<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>146<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>X2+I<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>\u2022 Prohibits rising edge interrupt of X2. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"4\">\n<p>EN<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>DIS<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u2022 Output to clear error counter of servo <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>M50<\/p>\n<\/td>\n<td>\n<p>driver. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u2022 Sets the homing completion signal. <\/p>\n<p>74.IMDIO<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td>\n<p>D<\/p>\n<\/td>\n<td>\n<p>:  Y8<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Sends output immediately.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>N<\/p>\n<\/td>\n<td>\n<p>:   1<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>69<\/p>\n<p>RTI<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-291.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> Program Example 2: Machine homing (method 2) <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>X3: Connected to near home sensing input, and configured as falling edge interrupt input. <\/p>\n<p>\u3010Main Program\u3011<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>M1924<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td>\n<p>67<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>INIT<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>CALL<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>65<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"3\">\n<p>Homing<\/p>\n<\/td>\n<td colspan=\"3\">\n<p>LBL<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>HOME<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>RST<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>M50<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>M20<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>\u2022 Clears the homing completion signal. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Servo<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Manual<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>Leftover<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\" rowspan=\"4\">\n<p>Ready<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>operation<\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"4\">\n<p>travel limit<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>M20<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u2022 Clears the instruction completion <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>signal for homing.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"6\">\n<p>M20<\/p>\n<\/td>\n<td colspan=\"5\" rowspan=\"5\">\n<p>Servo<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>RST<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>M5<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>M4<\/p>\n<\/td>\n<td>\n<p>\u2022 Clears the step pointer, it starts from <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"5\">\n<p>the first step to execute.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>D<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>R2014<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>RST<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>Ready<\/p>\n<\/td>\n<td>\n<p>M5<\/p>\n<\/td>\n<td>\n<p>M50<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>M4<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>M4<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>X3<\/p>\n<\/td>\n<td colspan=\"4\">\n<p>145P<\/p>\n<\/td>\n<td rowspan=\"7\">\n<p>ACT<\/p>\n<\/td>\n<td rowspan=\"13\">\n<p>M1006<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Enable X3\u2212 (falling edge) interrupt. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>EN\u2191EN<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>X3 &#8211; I<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>M4<\/p>\n<\/td>\n<td colspan=\"4\">\n<p>140.HSPSO<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Configure R5000\uff5eR5199 to be the <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\" rowspan=\"4\">\n<p>Positioning Program\uff1a<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Ps<\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"2\">\n<p>:              0<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>read only register (ROR) before <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\" rowspan=\"2\">\n<p>SR<\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"2\">\n<p>:  R    5040<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>programming, after then, when storing <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\" rowspan=\"2\">\n<p>001 SPD R2919 <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>PAU<\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"3\">\n<p>WR<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>:  R    2014<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>ERR<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>program, the Ladder program will <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>DRV ADR,\u2212,999999,Ut <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>EXT X3 <\/p>\n<\/td>\n<td colspan=\"4\" rowspan=\"3\">\n<p>ABT<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>DN<\/p>\n<\/td>\n<td>\n<p>automatically contains the positioning <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>GOTO NEXT <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>program.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>002 SPD  1000 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>DRV ADR,\u2212,1000,Ps <br \/>WAIT TIME,10 <br \/>GOTO NEXT <br \/>003 SPD  R200 <br \/>DRV ADR,+,999999,Ut <br \/>MEND <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>M4<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>M1996<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>SET<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M5<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>TUP<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>M51<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Homing instruction completed.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>M50<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>M51<\/p>\n<\/td>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>SET<\/p>\n<\/td>\n<td>\n<p>Y8<\/p>\n<\/td>\n<td>\n<p>\u2022 Signal for homing completion.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>Y8<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td>\n<p>.01S<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>30<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Output to clear error counter of servo <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>T0<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>driver &#8212; Y8 is ON for 0.3 second.<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>T0<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>RST<\/p>\n<\/td>\n<td>\n<p>Y8<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>08D.MOV<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td>\n<p>S<\/p>\n<\/td>\n<td>\n<p>:               0<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Fill the current PS registers with 0.<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>D<\/p>\n<\/td>\n<td>\n<p>:   R   4088<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-292.png\" \/><\/p>\n<p>\u3010Sub Program\u3011<\/p>\n<p>65<\/p>\n<p>LBL \tINIT<\/p>\n<p>146<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>DIS<\/p>\n<\/td>\n<td>\n<p>X3 &#8211; I<\/p>\n<\/td>\n<td>\n<p>\u2022 Prohibits X3\u2212 interrupt <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>141.MPARA<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>68<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td>\n<p>Ps<\/p>\n<\/td>\n<td>\n<p>:    0<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>ERR<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Parameter table R2900\uff5eR2923 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>SR<\/p>\n<\/td>\n<td>\n<p>:  2900<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>RTS<\/p>\n<p>65<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"6\">\n<p>M4<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>LBL<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>X3 &#8211; I<\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"2\">\n<p>142<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>0<\/p>\n<\/td>\n<td>\n<p>y X3 falling edge interrupt service <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>subroutine. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>PSOFF<\/p>\n<\/td>\n<td>\n<p>\u2022 Stops pulse output immediately <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>X3 &#8211; I<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Prohibits X3\u2212 interrupt <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>146<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>ENDIS<\/p>\n<\/td>\n<td>\n<p>\u2022 Sets the homing completion signal.<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>69<\/p>\n<p>RTI<\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-293.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-294.png\" \/><\/p>\n<p>The above two machine homing examples are implemented by using Ladder program; although it is not difficult to understand, but it\u2019s a bit cumbersome to use, which might be inconvenient for users. Since FATEK is taking into account the customer\u2019s utility and convenience, we add machine zero return command (DRVZ) in high-speed pulse output instruction (FUN140), which provides 3 modes (MD0~MD2) of operation for different application requirement, of FBs series PLC system version (OS) V4.32 (including) or later versions. <\/p>\n<p>When using DRVZ command for machine homing, it should conjoining the FUN141 motion parameter\u2019s setting of machine zero related, it can be listed as below: <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>Parameter 6  (Creep speed) <\/p>\n<\/td>\n<td>\n<p>DRVZ MD0 <\/p>\n<\/td>\n<td>\n<p>DRVZ MD1 <\/p>\n<\/td>\n<td>\n<p>DRVZ MD2 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Must be <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Parameter 9-1 (Return direction) <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Parameter 15-0 (DOG input) <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Parameter 15-1 (Limit input) <\/p>\n<\/td>\n<td>\n<p>Optional <\/p>\n<\/td>\n<td>\n<p>Optional <\/p>\n<\/td>\n<td>\n<p>Optional <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Parameter 15-2 (PG0 input) <\/p>\n<\/td>\n<td>\n<p>No need <\/p>\n<\/td>\n<td>\n<p>No need <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Parameter 15-3 (CLR output) <\/p>\n<\/td>\n<td>\n<p>Optional <\/p>\n<\/td>\n<td>\n<p>Optional <\/p>\n<\/td>\n<td>\n<p>Optional <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Parameter 16  (Zero point address) <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Parameter 17  (No. of PG0 signal) <\/p>\n<\/td>\n<td>\n<p>No need <\/p>\n<\/td>\n<td>\n<p>No need <\/p>\n<\/td>\n<td>\n<p>Must be <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>The FUN 140 instruction can\u2019t be executed for machine zero return while encountering the following situations with the error indications:<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"3\">\n<p> R4060(PS0) <\/p>\n<\/td>\n<td>\n<p>Error Code <\/p>\n<\/td>\n<td>\n<p> Explanation <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> 42 <\/p>\n<\/td>\n<td>\n<p>DRVZ can\u2019t follow DRVC <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p> 50 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Illegal operation mode of DRVZ <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p> R4061(PS1) <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p> 51 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Illegal DOG input <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p> R4062(PS2) <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p> 52 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>Illegal PG0 input <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p> R4063(PS3) <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p> 53 <\/p>\n<\/td>\n<td>\n<p>Illegal CLR output <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>The method of using DRVZ is same as the method of two modes (DRV and DRVC) of FUN140.  To see the details please choose MD0~MD2 of Movement Action mode of the servo program table in the project window (See below). <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-295.jpg\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-296.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-297.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-298.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-299.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-300.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-301.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-302.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-303.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-304.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-305.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-306.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-307.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-308.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-309.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-310.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-311.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-312.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-313.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-314.png\" \/><\/p>\n<p>Zero return (DRVZ) operation in detailed diagram description <\/p>\n<p>Mode 0 <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-315.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-316.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-317.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-318.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-319.png\" \/>\t<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-320.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-321.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-322.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-323.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-324.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-325.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-326.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-327.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-328.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-329.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-330.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u3010<strong>Description<\/strong>\u3011<\/p>\n<p>1\u2022 Zero return starts behind the DOG sensor (Parameter 15_0) <\/p>\n<p>a. Moving forward to zero direction in Zero Return Speed <br \/>b. Changing the moving speed by Creep Speed (Parameter 6) while sensing the dog sensor (Edge \t\tdetection and interrupt processing <br \/>c. Keeping forward until leaving the dog sensor (Edge detection and interrupt processing), it is the zero \t\thome position <br \/>d. If it doesn\u2019t configure the CLR output (Parameter 15_3) for servo driver, the zero return process has \t\tbeen finished at step c. <\/p>\n<p>e. If it has been configured the CLR output (Parameter 15_3) for servo driver, the zero return process \twill be finished after the CLR output with more than 20mS duration <\/p>\n<p> 2\u2022 Zero return starts at or in front of the DOG sensor (Parameter 15_0) + Stroke limit sensor (Parameter 15_1) <\/p>\n<p>a. Moving forward to zero direction in zero return speed, there will stop moving while sensing the limit sensor <\/p>\n<p>b. Moving backward in zero return speed and after leaving the dog sensor, it will drive the zero return procedures same as mentioned above 1. <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-331.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-332.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-333.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-334.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-335.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-336.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-337.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-338.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-339.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-340.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-341.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-342.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-343.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-344.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-345.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-346.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-347.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-348.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-349.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-350.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-351.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-352.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-353.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-354.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-355.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-356.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-357.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-358.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-359.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-360.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-361.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-362.png\" \/><\/p>\n<p>Mode 1 <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-363.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-364.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-365.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-366.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-367.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-368.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-369.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-370.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-371.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-372.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-373.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-374.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-375.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-376.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-377.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-378.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-379.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-380.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-381.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u3010<strong>Description<\/strong>\u3011<\/p>\n<p>1\u2022 Zero return starts behind the DOG sensor (Parameter 15_0) <\/p>\n<p>a. Moving forward to zero direction in Zero Return Speed <br \/>b. Auto slow down to stop movement while sensing the dog sensor (Edge detection and interrupt \tprocessing) <br \/>c. Delay 0.5 second, then moving backward until leaving the dog sensor (Edge detection and interrupt \tprocessing), it is the zero home position <br \/>d. If it doesn\u2019t configure the CLR output (Parameter 15_3) for servo driver, the zero return process has \tbeen finished at step c <br \/>e. If it has been configured the CLR output (Parameter 15_3) for servo driver, the zero return process \twill be finished after the CLR output with more than 20mS duration <\/p>\n<p> 2\u2022 Zero return starts at or in front of the DOG sensor (Parameter 15_0) + Stroke limit sensor (Parameter \t15_1) <\/p>\n<p>a. Moving forward to zero direction in zero return speed, there will stop moving while sensing the limit sensor <\/p>\n<p>b. Moving backward in zero return speed and after leaving the dog sensor, it will drive the zero return procedures same as mentioned above 1. <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-382.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-383.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-384.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-385.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-386.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-387.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-388.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-389.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-390.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-391.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-392.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-393.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-394.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-395.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-396.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-397.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-398.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-399.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-400.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-401.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-402.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-403.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-404.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-405.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-406.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-407.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-408.png\" \/><\/p>\n<p>Mode 2 (Front edge counting) <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-409.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-410.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-411.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"6\" rowspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-412.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-413.png\" \/><\/p>\n<\/td>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-414.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-415.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-416.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-417.png\" \/><\/p>\n<\/td>\n<td rowspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-418.png\" \/><\/p>\n<\/td>\n<td rowspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-419.png\" \/><\/p>\n<\/td>\n<td rowspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-420.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-421.png\" \/><\/p>\n<\/td>\n<td rowspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-422.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-423.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-424.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-425.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-426.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-427.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-428.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-429.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-430.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-431.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-432.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-433.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-434.png\" \/><\/p>\n<\/td>\n<td colspan=\"6\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-435.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-436.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"12\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-437.png\" \/>\t<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-438.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-439.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"11\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-440.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-441.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-442.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-443.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u3010<strong>Description<\/strong>\u3011<\/p>\n<p>1\u2022 Zero return starts behind the DOG sensor (Parameter 15_0) <\/p>\n<p>a. Moving forward to zero direction in Zero Return Speed <br \/>b. Changing the moving speed by Creep Speed (Parameter 6) while sensing the dog sensor (Edge \tdetection and interrupt processing), and start counting (Edge detection and interrupt processing) the \tPG0 signal (Parameter 15_2) <br \/>c. While the counting value of PG0 signal is equal to the present value (Parameter 17), it is the zero \thome position <br \/>d. If it doesn\u2019t configure the CLR output (Parameter 15_3) for servo driver, the zero return process has \tbeen finished at step c <br \/>e. If it has been configured the CLR output (Parameter 15_3) for servo driver, the zero return process \twill be finished after the CLR output with more than 20mS duration <\/p>\n<p> 2\u2022 Zero return starts at or in front of the DOG sensor (Parameter 15_0) + Stroke limit sensor (Parameter \t15_1) <\/p>\n<p>a. Moving forward to zero direction in zero return speed, there will stop moving while sensing the limit \tsensor <\/p>\n<p>b. Moving backward in zero return speed and after leaving the dog sensor, it will drive the zero return procedures same as mentioned above 1. <\/p>\n<p>\u203b Working at this mode, it should be noticed to adjust the correct position of dog sensor to incorporate with PG0 signal to avoid one count PG0 error for zero return processing <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-444.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-445.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-446.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-447.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-448.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-449.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-450.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-451.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-452.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-453.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-454.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-455.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-456.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-457.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-458.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-459.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-460.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-461.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-462.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-463.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-464.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-465.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-466.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-467.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-468.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-469.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-470.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-471.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-472.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-473.png\" \/><\/p>\n<\/td>\n<td colspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-474.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-475.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-476.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-477.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-478.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-479.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-480.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-481.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-482.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-483.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-484.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-485.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-486.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-487.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-488.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-489.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-490.png\" \/>\t<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-491.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-492.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-493.png\" \/><\/p>\n<\/td>\n<td rowspan=\"2\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-494.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-495.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-496.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-497.png\" \/>\t<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-498.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-499.png\" \/>\t<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-500.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-501.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-502.png\" \/>\t<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-503.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-504.png\" \/>\t<img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-505.png\" \/><\/p>\n<p>\u3010<strong>Description<\/strong>\u3011<\/p>\n<p>1\u2022 Zero return starts behind the DOG sensor (Parameter 15_0) <\/p>\n<p>a. Moving forward to zero direction in Zero Return Speed <br \/>b. Changing the moving speed by Creep Speed (Parameter 6) while sensing the dog sensor (Edge \tdetection and interrupt processing); keeping forward and start counting (Edge detection and interrupt \tprocessing) the PG0 signal (Parameter 15_2) while leaving the dog sensor <br \/>c. While the counting value of PG0 signal is equal to the present value (Parameter 17), it is the zero \thome position <br \/>d. If it doesn\u2019t configure the CLR output (Parameter 15_3) for servo driver, the zero return process has \tbeen finished at step c <br \/>e. If it has been configured the CLR output (Parameter 15_3) for servo driver, the zero return process \twill be finished after the CLR output with more than 20 mS duration <\/p>\n<p>2\u2022 Zero return starts at or in front of the DOG sensor (Parameter 15_0) + Stroke limit sensor (Parameter \t15_1) <\/p>\n<p>a. Moving forward to zero direction in zero return speed, there will stop moving while sensing the limit \tsensor <\/p>\n<p>b. Moving backward in zero return speed and after leaving the dog sensor, it will drive the zero return procedures same as mentioned above 1. <\/p>\n<p>\u203bWorking at this mode, it should be noticed to adjust the correct position of dog sensor to incorporate with PG0 signal to avoid one count PG0 error of zero return processing <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-506.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-507.png\" \/><\/p>\n<p>The above three homing completion modes assume that starting point is nearly the right side of DOG sensor. But when implementing homing action, the starting point is possible located after DOG sensor or exactly located on DOG sensor.  The following diagram and description are interpreted the homing action of two locations: <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"2\">\n<p>Zero return starts at or in front of the DOG sensor <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-508.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-509.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-510.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-511.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-512.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-513.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-514.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-515.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-516.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\" rowspan=\"2\">\n<p>Steps <\/p>\n<p>\tg operation has started, it moves toward the homing direction (Parameter 9_1) in zero return speed \tuntil strokes the switch of limit input point (Parameter 15_1).<\/p>\n<p>\tkes the limit input point (Parameter 15_1), it immediately moving backward to the homing direction \tuntil leave the DOG sensor (sensor signal from 1 \u2192 0). <\/p>\n<p>\ttion of the Step 2, you can determine that the starting point has returned back to the right of DOG \tsensor, and then it will complete the homing operation as we set the homing mode (MD0~MD2) earlier. <\/p>\n<\/td>\n<\/tr>\n<tr><\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-517.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-518.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-519.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-520.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-521.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-522.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-523.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-524.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-525.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-526.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-527.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-528.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-529.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-530.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-531.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-532.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-533.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-534.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-535.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-536.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-537.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-538.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-539.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-540.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-541.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-542.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-543.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-544.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-545.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-546.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-547.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-548.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-549.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-550.png\" \/><\/p>\n<p> Program Example 3\uff1aMachine homing\uff08by using Mode 2 of DRVZ command\uff09<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-551.png\" \/><\/p>\n<\/td>\n<td>\n<p>\u2022 M1924 initial\/end pulse set the parameter of the servo parameter command into the <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>system. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-552.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-553.png\" \/><\/p>\n<\/td>\n<td>\n<p>\u2022 Clears FUN140 homing completing signal. <\/p>\n<p>\u2022 Homing operation has started. <\/p>\n<p>\u2022 FUN140 operates DRVZ command. <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-554.png\" \/><\/p>\n<p> Servo Parameter Table(FUN141) Setting <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-555.jpg\" \/><\/p>\n<p> Servo Program Table(FUN140) Setting <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-556.jpg\" \/><\/p>\n<p>Program Description<strong>:<\/strong><\/p>\n<p>(1).  When the program has been executed, the initial pulse (M1924) will set the starting address of servo parameters \ttable. <\/p>\n<p>(2).  When M0 is from 0\u21921 (Pinstruction), the self-holding loop M1 has started and at the same time FUN140 homing \toperation has also started. <\/p>\n<p>(3).  According to FUN140 the servo program table setting, first the speed toward to homing return direction (left) is 5000 until it touches the DOG points (X2), it immediately drops the speed to 1000 and starts PG0 counting. <\/p>\n<p>(4).  When zero signal counting (X4) has reached its setting value 10, it finds the home position.  Zero clear signal (Y8) sent to \u201cON\u201d more than 20mS and as well as the machine zero position value, set to 100, moves to current register. <\/p>\n<p>(In this example we use 0 axis, then set the value 100 to DR4088), then the homing operation has completed. <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-557.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-558.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-559.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-560.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-561.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-562.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-563.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-564.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-565.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-566.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-567.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-568.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-569.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-570.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-571.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-572.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-573.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-574.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-575.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-576.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-577.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-578.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-579.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-580.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-581.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-582.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-583.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>Diagram <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-584.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-585.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-586.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-587.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-588.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-589.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-590.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-591.png\" \/><\/p>\n<\/td>\n<td colspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-592.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-593.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-594.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-595.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-596.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-597.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-598.png\" \/><\/p>\n<\/td>\n<td rowspan=\"3\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-599.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-600.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-601.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-602.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-603.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-604.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-605.png\" \/><\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-606.png\" \/><\/p>\n<\/td>\n<td>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-607.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-608.png\" \/><\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-609.png\" \/><\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u203b When set the DOG point, it should be the input points (X0~X15) of main unit. <\/p>\n<p>\u203b When the input DOG point has been set, it cannot be conflict with interrupt and high-speed counter, for example: if X0 <\/p>\n<p>has been set for DOG point, then X0 cannot be set to an interrupt input or high-speed counter. <\/p>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-610.png\" \/><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-611.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> Program Example 4: JOG Forward <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"3\">\n<p>Jog forward button<\/p>\n<\/td>\n<td rowspan=\"7\">\n<p>M1<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>RST<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1<\/p>\n<\/td>\n<td rowspan=\"7\">\n<p>M0<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Clears the completion signal <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"3\">\n<p>\u2191<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>Jog <\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>Servo<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>Manaul<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>D<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>R  2000<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Starts from the first step every <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"4\">\n<p>EN<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>RST<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>jog execution. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>forward <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>button<\/p>\n<\/td>\n<td>\n<p>Ready<\/p>\n<\/td>\n<td>\n<p>operation<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>M0<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"7\">\n<p>M0<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>Positioning program: <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>140.HSPSO<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>ACT<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1000<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps<\/p>\n<\/td>\n<td>\n<p>:              0<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>PAU<\/p>\n<\/td>\n<td>\n<p>SR<\/p>\n<\/td>\n<td>\n<p>:  R    5000<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>ERR<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>M1001<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>001 SPD 1000 <\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>WR<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>:  R    2000<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>DRV ADR,+,1,Ps <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>WAIT TIME,50 <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>ABT<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>DN<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>GOTO NEXT <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>002 SPD R2907 <br \/>\tDRV ADR,+,99999999,Ut <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"3\">\n<p>M0<\/p>\n<\/td>\n<td>\n<p>MEND <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>SET<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>M1<\/p>\n<\/td>\n<td>\n<p>\u2022 As the execution of last step <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>M1996<\/p>\n<\/td>\n<td>\n<p>completed, it sets up the <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>completion signal.<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> Program Example 5: JOG Backward <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td colspan=\"2\">\n<p>Jog backward button<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>M3<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>RST<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M3<\/p>\n<\/td>\n<td rowspan=\"5\">\n<p>M2<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Clears the completion signal. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>\u2191<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>\tJog <br \/>backward Servo<\/p>\n<p>button \tReady<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>Manaul <br \/>operation<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>D<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>R  2007<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Starts from the first step every <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>RST<\/p>\n<\/td>\n<td>\n<p>jog execution.<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>M2<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"6\">\n<p>M2<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>Positioning Program <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td colspan=\"2\">\n<p>140.HSPSO<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>ACT<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1003<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps<\/p>\n<\/td>\n<td>\n<p>:              0<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"4\">\n<p>PAU<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>SR<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>:  R    5020<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>ERR<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>M1004<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>001 SPD 1000 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"2\">\n<p>WR<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>:  R    2007<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>DRV ADR,\u2212,1,Ps <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>WAIT TIME,50 <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>GOTO NEXT <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>ABT<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>DN<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>002 SPD R2907 <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>DRV ADR,\u2212,99999999,Ut <br \/>MEND <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"3\">\n<p>M2<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>M1996<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>SET<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>M3<\/p>\n<\/td>\n<td>\n<p>\u2022 As the execution of the last step <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>completed, it sets up the <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>completion signal.<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p><img decoding=\"async\" src=\"https:\/\/resource.fatek.com\/wp-content\/uploads\/fatek\/fbs-hw-en-011\/fbs-hw-en-011-612.png\" \/><\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p> Program Example 6: Step by step, One cycle, Continuous positioning control. <\/p>\n<\/td>\n<td><\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>M93 : Start <br \/>M101 : Step by step operation mode <br \/>M102 : One cycle operation mode <br \/>M103 : Continuous operation mode <br \/>M104 : Regular shut down. <\/p>\n<p>M105 : Emergency stop. <\/p>\n<p>M93<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"6\">\n<p>\u2191<\/p>\n<\/td>\n<td rowspan=\"6\">\n<p>M101<\/p>\n<\/td>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>RST<\/p>\n<\/td>\n<td>\n<p>M7<\/p>\n<\/td>\n<td>\n<p>\u2022 Clears shut down signal. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>RST<\/p>\n<\/td>\n<td>\n<p>M1010<\/p>\n<\/td>\n<td>\n<p>\u2022 Clears the error signal. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>EN<\/p>\n<\/td>\n<td>\n<p>RST<\/p>\n<\/td>\n<td>\n<p>M1011<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Clears the step completion signal. <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>RST<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>R   2021<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>\u2022 Except step by step mode, the step <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>pointer is cleared to be 0; it starts <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>from the first step to execute. <\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>M93<\/p>\n<\/td>\n<td>\n<p>SERVO<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M105<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1010<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>RST<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>R   2022<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M6<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>\u2022 Clears being active bit of FUN140 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>READY<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u2191<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td>\n<p>M6<\/p>\n<\/td>\n<td>\n<p>M101<\/p>\n<\/td>\n<td>\n<p>M1011<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>EN<\/p>\n<\/td>\n<td colspan=\"2\" rowspan=\"2\">\n<p>140.HSPSO<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>ACT<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>M1009<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td rowspan=\"7\">\n<p>M6<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M101<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M7<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>Ps<\/p>\n<\/td>\n<td>\n<p>:              0<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>Positioning program: <\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>PAU<\/p>\n<\/td>\n<td>\n<p>SR<\/p>\n<\/td>\n<td>\n<p>:  R    5100<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>ERR<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1010<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>001 SPD   1000 <\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>WR<\/p>\n<\/td>\n<td rowspan=\"4\">\n<p>:  R    2021<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>DRV   ADR,+,20000,Ut <\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>ABT<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>DN<\/p>\n<\/td>\n<td rowspan=\"3\">\n<p>M1011<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>WAIT  TIME,100 <\/p>\n<\/td>\n<\/tr>\n<tr>\n<td colspan=\"2\">\n<p>GOTO NEXT <\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>002 SPD  20000 <br \/>\tDRV  ADR,+,40000,Ut <br \/>\tWAIT M200 <br \/>\tGOTO NEXT <br \/>003 SPD  25000 <br \/>\tDRV  ADR,\u2212,50000,Ut <br \/>\tWAIT TIME,500 <br \/>\tGOTO NEXT <br \/>004 SPD  5000 <br \/>\tDRV  ADR,\u2212,10000,Ut <br \/>\tWAIT X16 <br \/>\tGOTO 1<\/p>\n<div class=\"fatek-tw\">\n<table>\n<tr>\n<td rowspan=\"2\">\n<p>M6<\/p>\n<\/td>\n<td>\n<p>M102<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M104<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M1996<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>EN<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>SET<\/p>\n<\/td>\n<td rowspan=\"2\">\n<p>M7<\/p>\n<\/td>\n<\/tr>\n<tr>\n<td>\n<p>M103<\/p>\n<\/td>\n<\/tr>\n<\/table>\n<\/div>\n<p>\u2022 Set up the shut down signal.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>People use ordinary motor to exercise positioning contr [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[33],"tags":[],"class_list":["post-3416","post","type-post","status-publish","format-standard","hentry","category-en-fbs-hw"],"_links":{"self":[{"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/posts\/3416","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/comments?post=3416"}],"version-history":[{"count":0,"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/posts\/3416\/revisions"}],"wp:attachment":[{"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/media?parent=3416"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/categories?post=3416"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/resource.fatek.com\/index.php\/wp-json\/wp\/v2\/tags?post=3416"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}