Posted in

By

8 of 13Updated 2026-11-179 min read中文版

7 Power Supply Wiring & Power Consumption Calculation and Power Sequencing Requirements

Power Supply Wiring & Power Consumption Calculation and Power Sequencing Requirements

There are two kinds of power for M series PLC power module. The 1st one is CPU dedicated power supply (To CPU & high speed or local I/O Expansion modules). The 2nd one is external Sensor power supply. The CPU module and the expansion module are also divided in 2 parts of circuits. The 1st one is 24VDC (Internal Circuit), the 2nd one is 24VDC (Output Sensor Circuit). The 24VDC (Internal Circuit) is supplied by the CPU dedicated power supply of the M series PLC power module. The 24VDC (Output Sensor Circuit) can be supplied by an external power supply or by the external Sensor power supply of the M series PLC power module. Neither the CPU module nor the expansion module has internal power supply, and both must consume the power of the power module to supply power. 

⚠Caution

In industrial environments, main power may irregularly experience a surge current or high voltage pulse caused by the start or shut down of high power equipment. Users are advised to take necessary measures (for example, the use of isolation transformer or other MOV suppression devices) for the protection of PLC and its peripherals. 

⚠Caution

Dans les environnements industriels, l’alimentation principale peut subir de manière irrégulière des surtensions de courant ou des impulsions de haute tension, provoquées par la mise en marche ou l’arrêt d’équipements de forte puissance. Il est recommandé aux utilisateurs de prendre les mesures nécessaires (par exemple l’utilisation d’un transformateur d’isolement ou d’autres dispositifs de suppression tels que les varistances MOV) afin de protéger le PLC et ses périphériques.

7-1 Specifications and Wiring of Power Module

Power Module Specification Table

Specification Model

MPA024-24

MPA048-24

MRPWE-AC

input

Input Voltage

100~240VAC

100~240VAC

100~240VAC

Input Frequency

50/60Hz

50/60Hz

50/60Hz

Max. Input Current

1A max.

1A max.

1A max.

Inrush Current (Cold Start)

22A/115Vac (44A/230Vac)

22A/115Vac (44A/230Vac)

22A/115Vac (44A/230Vac)

Withstand voltage

3,000 VAC (Primary-secondary),

1,500 VAC (Primary-PE),

500 VAC(Secondary-PE)

3,000 VAC (Primary-secondary),

1,500 VAC (Primary-PE),

500 VAC(Secondary-PE)

3,000 VAC (Primary-secondary),

1,500 VAC (Primary-PE),

500 VAC(Secondary-PE)

Insulation resistance

>100MΩ/500VDC

>100MΩ/500VDC

>100MΩ/500VDC

Fuse Spec.

2A

2A

2A

Hold-up time

>15ms/ 115VAC,

>60ms/ 220VAC

>15ms/ 115VAC,

>60ms/ 220VAC

>15ms/ 115VAC,

>60ms/ 220VAC

Isolation Type

Transformer/ Photocoupler Isolation,1500VAC/1 minute

Transformer/ Photocoupler Isolation,1500VAC/1 minute

Transformer/ Photocoupler Isolation,1500VAC/1 minute

Operation indication

LED (green)

LED (green)

LED (green)

output

Rated output power

24W (Shared CPU dedicated power supply and external Sensor power supply)

48W (Shared CPU dedicated power supply and external Sensor power supply)

48W (Shared CPU dedicated power supply and external Sensor power supply)

Rated output current

1A (Shared CPU dedicated power supply and external Sensor power supply)

2A (Shared CPU dedicated power supply and external Sensor power supply)

2A (Shared CPU dedicated power supply and external Sensor power supply)

Output voltage range

24VDC±1%

24VDC±1%

24VDC±1%

Conversion efficiency

86%/110VAC,87%/220VAC

86%/110VAC,87%/220VAC

86%/110VAC,87%/220VAC

Protection

Overvoltage protection

Latching overvoltage protection, re-power on to recover 34V~36V

Latching overvoltage protection, re-power on to recover 34V~36V

Latching overvoltage protection, re-power on to recover 34V~36V

Overcurrent protection

Method: Foldback overload protection, automatically recover when overload is removed 101%~133% rated output power

Method: Foldback overload protection, automatically recover when overload is removed 101%~133% rated output power

Method: Foldback overload protection, automatically recover when overload is removed 101%~133% rated output power

Environmental Specifications

Operating Ambient Temperature

0℃~55℃

0℃~55℃

0℃~55℃

Relative Humidity

20 ~ 90% (non-condensing)

20 ~ 90% (non-condensing)

20 ~ 90% (non-condensing)

Storage Temperature

-25 ~ +70℃

-25 ~ +70℃

-25 ~ +70℃

Certifications

CE

CE

CE

External dimensions

90mmX33.7mmX90mm

90mmX33.7mmX90mm

90mmX46.2mmX90mm

⚠Caution

The schematic diagram of power module is shown below. Also be cautious about the following:

  1. Please follow the wiring schemes regulated by local national standards to use single-pole switch(break hot wire〝L〞), or double-pole switch(break both〝L〞and〝N〞), to turn on or off the AC input power.
  2. In wiring, hot wire〝L〞must be connected to the L terminal on unit, while the ground line〝N〞connected to the N terminal. Please use wires with diameters ~.
  3. All terminals on CPU module or Power module have to be connected to the EG (Earth Ground) terminal of main power system as shown in the figure below, with wire diameters larger than .

⚠Caution

Le schéma de principe du module de puissance est illustré ci-dessous. Il convient également de faire attention aux points suivants :

  1. Veuillez suivre les schémas de câblage réglementés par les normes nationales locales pour utiliser l’interrupteur unipolaire(break hot wire〝L〞), ou l’interrupteur bipolaire(break both〝L〞and 〝N〞), pour allumer ou éteindre l’alimentation en courant alternatif.
  2. Lors du câblage, le fil chaud〝L〞 doit être connecté à la borne L de l’appareil, tandis que le fil de terre〝N〞doit être connecté à la borne N. Utilisez des fils de diamètre ~.
  3. Toutes les bornes du module CPU ou du module d’alimentation doivent être connectées à la borne EG (Earth Ground) du système d’alimentation principal, comme indiqué dans la figure ci-dessous, avec des fils d’un diamètre supérieur à .

⚠Warning

24VDC Output power for Sensor circuit cannot be connected in parallel with other powers, in which the conflict between two sets of power will decrease their lifetime or cause immediate damage. This will induce unexpected malfunction of PLC and cause serious or even deadly damage to people or equipment.

⚠ Avertissement

L’alimentation de sortie 24VDC pour le circuit du capteur ne peut pas être connectée en parallèle avec d’autres alimentations, dans lesquelles le conflit entre deux ensembles d’alimentation réduira leur durée de vie ou causera des dommages immédiats. Cela entraînerait un dysfonctionnement inattendu de l’automate et causerait des dommages graves, voire mortels, aux personnes ou à l’équipement.

PLC System Wiring

Power Supply Wiring Diagram

7-2 Maximum Current Consumption of Expansion Module

The CPU module and expansion modules themselves have no power supply and must be supplied by the M series PLC power module. The following table shows the maximum current consumption of each expansion module.

⚠Warning

Any output of M series PLC power module, the total amount of current cannot exceed the value listed in the below table. Any violation will cause a voltage drop by overloading the power supply, or intermittent powered with the supply in protection mode, either of which will result in unexpected action of PLC and cause harm to people or damage to equipment.

⚠ Avertissement

Pour toute sortie d’un module d’alimentation PLC de la série M, la quantité totale de courant ne peut pas dépasser la valeur indiquée dans le tableau ci-dessous. Toute violation entraînera une chute de tension en surchargeant l’alimentation, ou une alimentation intermittente avec l’alimentation en mode de protection, ce qui entraînera une action inattendue de l’automate et causera des dommages aux personnes ou à l’équipement.

Maximum Current Consumption of Expansion Module Table

Model Current Consumption

24VDC (Internal Circuit)

24VDC (Output Sensor Circuit)

Advanced and power Expansion Modules

Power Modules

MPA024-24

–

–

MPA048-24

–

–

Plug-in Expansion Boards

Communication

Plug-in Expansion Boards

MB-CB2

Approaches 0 mA

MB-CB5

Approaches 0 mA

DI Plug-in Expansion Boards

MB-2HSC

Approaches 0 mA

MB-4X

Approaches 0 mA

DO Plug-in Expansion Boards

MB-2PSO◇

Approaches 0 mA

MB-4Y◇

Approaches 0 mA

AI Plug-in Expansion Boards

MB-2ADL

20 mA

AO Plug-in Expansion Boards

MB-2DAL

80 mA

RTC Plug-in Expansion Boards

MB-RTC

Approaches 0 mA

High Speed Expansion Modules

High Speed Communication Modules

MHCM22

40mA

MHCM55

40mA

MHCM25

40mA

Local I/O Expansion Modules

DI Modules

M16X

70mA

7.5mA/ Point

DO Modules

M16YT

150mA

Max.0.5A/ Point

M16YJ

163mA

Max.0.5A/ Point

M16YR

90mA

Max.2A/ Point

DIO Combo Modules

M1616XYT

202mA

X :7.5mA
Y:0.5A/ Point

M1616XYJ

202mA

X :7.5mA
Y:0.5A/Point

M1616XYR

202mA

X :7.5mA

Y:@2A/Point

AI Modules

M04AD

78.2mA

–

M04ADR

78.2mA

–

AO Modules

M04DA

14.2mA

107mA

M04DAR

14.2mA

107mA

AIO Combo Modules

M0202AH

22.58mA

39.85mA

Temperature measurement Modules

M04TC

30.7mA

–

M04TCR

30.7mA

–

Temperature Measurement

Combo Modules

M0202TH

30mA

–

Load Cell Modules

M02LC

40.64mA

–

M02LCR

56.1mA

–

End module

MRE

–

–

I/O Bus Extension modules

Repeater Modules

MRPWE-AC

–

–

I/O Bus Extension module(Head)

MRGH

–

–

I/O Bus Extension module(Tail)

MRGT

–

–

Remote Expansion Modules

Remote I/O Coupler

MC0EN

80mA

–

Maximum Current Consumption of CPU Module Table

Model Current

24VDC (Internal Circuit)

24VDC (Output Sensor Circuit)

CPU Modules

Compact CPU Modules

MQ2M0-1616◇

150mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MQ2M1-1616◇

150mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MQ2M3-1616◇

150mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MQ2M6-1616◇

150mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

Advanced CPU Modules

MA1N0-1616◇

150mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MA1N3-1616◇

150mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MA1I4-1616◇

150mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

General Motion Control CPU Module

MS2C4-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MS2C5-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MS3C6-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MU2C4-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MU2C6-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MU3C2-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MU3C3-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MU3C4-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MU3C5-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

MU3C6-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

Advanced Motion Control CPU Module

ME2C3-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

ME2C4-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

ME2C5-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

ME3C6-1616◇

200mA

DI : 7.5mA/Point

DO : Max.0.1A/Point

7-3 Calculation Example of Power Capacity

Power module selection is depending on the sum of current consumption of all modules. Therefore, user must know the current consumption of each module. Please refer to the maximum current consumption of expansion module table, which has the maximum current consumption of each expansion module.

User must consider the match between power and expansion modules cannot cause output power of any one group of overload use.

The below diagram is a System Modules, try to calculate the power supply used of the system.

Type

Power Module

CPU Module

Expansion Module

Expansion Module

Expansion Module

Expansion Module

END Module

Extra Capacity

Module Name

MPA024-

24

ME3C6-

1616T

M16XX

M16YT

M04AD

M04TC

MRE

24VDC

(Input Circuit)

+1000mA

-200mA

-70mA

-150mA

-78.2mA

-30.7mA

–

231.1mA

24VDC (Output Circuit)

-7.5mA*16 Point

-7.5mA*16 Point

–

–

–

–

  • Power Module – 24VDC (Input Circuit) – 24VDC (Output Circuit)
    【1000mA】–【200mA+70mA+150mA+78.2mA+30.7mA】-【(7.5mA*16)+(7.5mA*16)】=231.1mA

7-4 Requirement of Power Sequence in CPU Modlue & Expansion Module

When the power is on, the M Series PLC first detects the type and number of expansion module attached to its expansion interface and get the actual I/O configuration. Therefore, while the CPU module performs detection, the power in expansion module should be already UP, otherwise, the detected I/O configuration will not correct. Namely, the power of expansion module should be ON simultaneously or even earlier. There will be no time sequence error when CPU module/expansion module are connected together to one power. If the expansion module and CPU module powered by different powers (or the same power but different switches), or external power supply is used for expansion modules, time sequence of both powers should be considered. To solve the problem of the expansion module power not get ready before CPU module power does, M Series PLC provides a special R35367 register which can delay the detection time of I/O configuration. The time base of R35367 is 0.01sec with a default value of 0, which can be set from 0~1000 (1~10c), as shown in the figure below. If the expansion module power cannot be UP within 1sec after main unit power is ON, the R35367 time needs to be set longer to delay the detection by CPU. It cannot exceed 10sec, however, otherwise the configuration of expansion interface cannot be detected.

Power Timing Diagram

Was this page helpful?

Tip: press ← → to switch chapters, Ctrl+K to search