Posted in

By

17 of 24Updated 2026-11-174 min read中文版

FBs-32DGI is a multiplex input module. One 32DGI module can support up to 32 digits thumbwheel switch or 128

discrete switch inputs. Thanks to the I/O control chip that incorporated in this module, the update rate of the input status is

irrelevant to CPU scan time. The input refresh time of this module is mere 10 mS. Owing to the scan nature of PLC,

though the multiplex input task is not performed by CPU, the over-all refresh time of this input module is still constrained

by the CPU scan time if the scan time is larger than 10 mS.

Appearance

POW

FBs-32DGI

FG 24V+

24V- NC

D0 D1

D2 D3

D4 D5

D6 D7

D8 D9

D10 D11

D12 D13

D14 D15

NC S1

S2 S3

S4 S5

S6 S7

S8 NC

By using the multiplex input, users only need to connect the FBs-32DGI with 24 wires to achieve 32-digit inputs (or

128 switch points). While FBs-32DGI is only 4cm wide, it is a truly high-density, low-cost and labor-saving solution.

17.1 FBs-32DGI Specifications

Item

Specification

Remarks

Input points

32-digit DIP/128 independent switch points

Occupied Resources

8 IRs

Connector

30-pin boxed header

Control signal

Column Output– 8 dots SINK (NPN) output Row Output– 16 dots SOURCE output

Refresh rate

10mS

Insulation

Transformer (power) and optical separation (contact signal)

Status indicator

5VPWR LED indicator

Power supply and consumption

24V-15%/+20%, 40mA

Internal current

5V, 14mA

Working temperature

0 – 60°C

Storage temperature

20 – 80°C

Dimensions

40(W)×90(H)×80(D) mm

17.2 The Procedure of Using FBs-32DGI Module

Start

Connect input signals to the DIP/switch point
according to the FBs-32DGI pin layout and connect
a 24VDC source to the module.

Read values from the analog/digital IR
R3840~R3903 to retrieve the digital input reading of
the DIP/switch point.

End

17.3 FBs-32DGI I/O Address

Each FBs-32DGI module occupies 8 IRs (R3840~R3903) for I/O address. In general, WinProladder will automatically detect and calculate the actual I/O address occupied by the module installed on the system after connecting to the PLC. Users may refer to the I/O Module Number Configuration provided by WinProladder in order to find out the exact I/O address of each expansion module to facilitate programming.

17.4FBs-32DGI Hardware Description

FBs-32DGI pin layout

FBS-32DGI

Pin

Signal Name

Pin

Signal Name

1

FG

2

24V+(external)

3

24V-(external)

4

No Connection

5

D0

6

D1

7

D2

8

D3

9

D4

10

D5

11

D6

12

D7

13

D8

14

D9

15

D10

16

D11

17

D12

18

D13

19

D14

20

D15

21

No Connection

22

S1

23

S2

24

S3

25

S4

26

S5

27

S6

28

S7

29

S8

30

No Connection

FG

I

2

24V+

24V-
D0
D2

NC
D1
D3

D4

D5

D6

D7

D8

D9

D10

D11

D12

D13

D14

D15

NC
S2

S1
S3

S4

S5

S6

S7

S8

29

30

NC

[Aerial View]

The I/O control chip built in the module multiplexes the 32 digits of thumbwheel switch or 128 discrete switch inputs by eight times scan, each scan reads in 4 digits of thumbwheel switch or 16 discrete switch inputs. The input selection signals S1~S8 listed in the above table are all low active output signal(NPN output). The multiplex data input signals D0~D15 are sink type input signals. Each times of scan, data are read from D0~D15 inputs and stored in I/O control chip.

The status of 32 digits of thumbwheel switch or 128 discrete switch inputs are directly mapped to 8 input registers as shown in following table. The IR is the first input register allocated for corresponding module (IR’s range is R3840~R3903).

DIP switch input

IR

D15-D12

D11-D8

D7-D4

D3-D0

IR+0

DIG3

DIG2

DIG1

DIG0

IR+1

DIG7

DIG6

DIG5

DIG4

IR+2

DIG11

DIG10

DIG9

DIG8

IR+3

DIG15

DIG14

DIG13

DIG12

IR+4

DIG19

DIG18

DIG17

DIG16

IR+5

DIG23

DIG22

DIG21

DIG20

IR+6

DIG27

DIG26

DIG25

DIG24

IR+7

DIG31

DIG30

DIG29

DIG28

Single point switch input

IR

D15

D14

D13

D12

D11

D10

D9

D8

D7

D6

D5

D4

D3

D2

D1

D0

IR+0

I15

I14

I13

I12

I11

I10

I9

I8

I7

I6

I5

I4

I3

I2

I1

I0

IR+1

I31 – I16

IR+2

I47 – I32

IR+3

I63 – I48

IR+4

I79- I64

IR+5

I95 – I80

IR+6

I111- I96

IR+7

I127 – I112

17.5 FBs-32DGI Input Circuit Diagram

Thumbwheel switch module

24V+

NC

D1

D3

D5

D0

D11

8

S3

S5

S8

NC

Connection for

independent

switch input

D4

D8

S6S7

D12

D0

S5

S3S4

D4

8

S2

D8

8

S1

D12

8

D0

8

D4

8

D8

8

S7

D12

8

D7

D9

D13

D15

S1

24V-

24V+

2

FG

24V-

D0

D2

D4

D6

D8

D10

D12

D14

NC

S2

S4

S6

S8

30

1

29

Was this page helpful?

Tip: press ← → to switch chapters, Ctrl+K to search